cooling run 中文意思是什麼
cooling run
解釋
冷機運轉-
Temp maintain, cooling, rinsing, chemical tank feeding, mixing, dye liquor run back, wash tank, drain out, alarm, process finish
藥攪拌回水洗桶排水報警程式完成等均可編入染 -
E. g water inlet, start main pump, heating, temp maintain, cooling, rinsing, chemical tank feeding, mixing, dye liquor run back, wash tank, drain out, alarm, process finish
3循環泵浦強力攪拌，能快速化鹽4自動洗桶自動 -
It has many good qualities such as energy saving, simply structured, cheaply and easily to operate and maintain, there is no revolving parts in the cooling part and can be run with liquid. for the above - mentioned reasons, the thermal separator has a lot of applications in chemical processes and engineering transformation, especially in the fields of liquid products recover from associated gas in oil field or light hydrocarbon gas in torch line, dehydrate natural gas, provides cold resource for scientific research
熱分離機是一種高效節能的新型氣體膨脹製冷裝置，具有結構簡單、造價低廉、操作維護方便、壽命長、製冷部分無轉動件及可以帶液運行等特點，有廣闊的應用前景，並已在油田伴生氣或火炬管線中輕烴的回收、天然氣脫水、為科學研究提供冷源等場合得到應用。 -
In this task, a test _ bed for engineering vehicles was developed based on virtual instrument. the whole system comprised 5 parts : the checking of running velocity, which was gotten on the test bed through the vehicles simulating real road running ; the temperature checking of the important points on the transmission system ; the temperature checking of the circling cooling water on the exit port of dynamometers ; the control of the loading power. which was given to vehicles by the power measuring machine ; the control of the total test - run time
本課題開發的基於虛擬儀器的工程機械跑合試驗臺，其測量和控制參數有：行駛速度檢測（車輛在跑合試驗臺上模擬路面的行駛速度） ；傳動系溫度檢測（試驗車輛傳動系主要部位多點溫度） ；冷卻水溫度檢測（測功機循環冷卻水出口溫度） ：加載功率控制（測功機施加給車輛的載荷） ；跑合時間控制（試驗車輛在試驗臺上加載跑合的總時間） 。 -
The preparing work before test run : first organize test run guide group consisted of supply party, demand party and installation party to check the installed qualified equipment ( machine, electricity, liquid, gas ) in an all - round way to see that circuit, water - way, gas - way and oil - way are switched on ; that all fastener, bolts and nuts are tight ; that all lubricating points and cooling points are put in position
試運轉前的準備工作：首先應組織有關（供方、需方、安裝）等單位參加的試車領導小組，對已安裝合格的設備（機、電、液、氣）進行全面的檢查，電路、水路、氣路、油路是否接通，所有設備的緊固件、螺栓、螺母等是否擰緊，各潤滑點和冷卻點是否到位。 -
Therefore, it is necessary for us to conduct a series of principle analysis on different sections of the station such as the fuel system, lube system and cooling system of the diesel engine for generators, and the shaft generator as well as the main switchboard etc. it is also important to carry out at meantime a number of reliability tests and analyze the test results so as to assure all the units of the station will run smoothly
因此，我們通過對船舶電站中柴油機的供油系統、潤滑系統、冷卻系統、軸帶發電機、主配電板等各個環節從原理上進行分析，並進行必要的可靠性試驗，對試驗數據進行分析，確保船舶電站各個環節的運行良好。
分享友人