crankshaft position 中文意思是什麼

crankshaft position 解釋
曲軸位置
  • crankshaft : 【機械工程】曲軸，機軸。
  • position : n 1 位置；方位；地點。2 處境，情況；狀態，形勢，局面。3 姿態，姿勢。4 地位，身份；職位；職務。5 ...
  1. Cps crankshaft position sensor

    曲軸位置傳感器
  2. ( 2 ) the crack compares with one depth with the first steps and the second steps natural frequency vibration, crack position near crank arm and main shaft transition round natural frequency little place under crankshaft ; with the third steps and the fourth steps natural frequency vibration, the smaller close to the second crank arm of crankshaft and round place natural frequency of the main shaft transition the position is

    （ 2 ）裂紋同一深度比以第1階和第2階固有頻率振動，裂紋位置越靠近曲軸中間曲柄臂與主軸過渡圓處固有頻率越小；以第3階和第4階固有頻率振動，位置越靠近曲軸第二個曲柄臂與主軸過渡圓處固有頻率越小。
  3. The key position bolt of the engine include connecting rod, crankshaft, main bearing, cylinder head, flywheel and shock absorber bolt, all of which belong to bolt fastening

    發動機關鍵工位螺栓包括連桿螺栓、曲軸螺栓、主軸承蓋螺栓、氣缸蓋螺栓、飛輪螺栓和減振器螺栓等均屬螺紋聯接。
  4. After reading a large amount of domestic and international about shaft research materials, the thesis combines the concrete experimental condition of the laboratory, and the crankshaft crack modal parameter characteristic go on the theoretical research at different depth different position to smoothshaft, experimental study, test data processing, diagnose system developing work ect

    本論文在閱讀了大量國內外關于軸裂紋檢測的研究資料后，結合實驗室的具體試驗條件，對光軸和曲軸裂紋在不同深度不同位置時模態參數特性進行理論研究、試驗研究、試驗數據處理、診斷系統開發等工作。
  5. Ckps crankshaft position sensor

    曲軸位置傳感器
  6. The structure of this magnetic inducting crankshaft position sensor assembly is simple, reliable easy for installation and use, being a crucial part of electronically controlled engine. as one of the important input signal of ecu controller, the sensor assembly can transmit stable cranking signal under any rotating speed of engine and ensures the stability of the performance of electronically controlled engine in respect of oil consumption, exhaust and output

    該磁感應式曲軸位置傳感器總成結構簡單，工作可靠，安裝使用方便，是電控發動機重要關鍵的部件作為ecu控制器重要的輸入信號之一，該傳感器總成能在發動機任何轉速輸出穩定的曲軸角度信號，可確保電控發動機在油耗排放輸出功率方面的性能保持穩定。
  7. Utilizing the principle of the smoothshaft to open 0. 4 mm crankshaft to the width of crack : ( 1 ) when it compares with one position crack, crankshaft natural frequency as crack depth than increase and reducing constantly

    利用光軸的原理對裂紋寬度為0 . 4mm的曲軸進行研究得出： （ 1 ）裂紋同一位置比時，曲軸固有頻率隨著裂紋深度比的增大而不斷減小。
  8. Crankshaft position sensor replacement

    更換曲軸感應器
  9. Crankshaft position sensor assembly

    凸輪軸位置傳感器
分享友人
分享到 Line

分享到臉書