crosstalk effect 中文意思是什麼
crosstalk effect
解釋
串音效應-
For high stability of the system, with the realization of hardware of the system, the second part of this paper starts from the transmission line theory, and studies the signal integrity problem of high - speed circuit system in light current. the causes of these signal integrity problems, such as signal delay, reflection, crosstalk, ground bounce noises and etc. are analyzed in theory. combined with actual design, key points of design and standard design flow of general high - speed, high - precision printed circuit board are summarized, which has been applied in actual system, and good effect has been achieved
為使系統具有較高的穩定性，本文第二部分結合該處理器的硬體實現，從傳輸線理論出發，研究了弱電情況下高速電路印刷電路板中的信號完整性問題；從理論上分析了延遲、反射、串擾以及地彈噪聲等信號完整性問題產生的原因；結合實際設計，總結了一般高速、高精度印刷電路板的設計要點和標準設計流程，並在實際系統中獲得了應用，取得了很好的效果。 -
An algorithm to resolve the coupling effect problem is proposed during the cross point assignment ( cpa ) stage. in the algorithm, the priority queue concept and the rip - up and reroute strategy are combined to control crosstalk noise caused by interconnect coupling capacitance. first, the nets are arranged into different priority queues according to their weighted sum of their length and criticality. then, the cpa problem for one queue of nets is translated into a linear assignment problem. after the assignment of one queue of nets, a post - cpa checking routine is performed to check and rip up the net pairs which violate the crosstalk noise constraint and then push them into the next queue to be reassigned. the algorithm is tested by a set of bench mark examples, and the experimental results are promising
提出了一種在過點分配階段解決噪聲耦合效應問題的演算法.該演算法採用優先隊列同拆線重布策略相結合的方法，控制由互連線耦合電容引起的串擾噪聲.演算法中，首先按照線長和約束限制，將線網劃分到若干個優先隊列中.然後，將每個優先隊列的過點分配問題轉換為線性分配問題.在完成一個線網隊列的分配后，通過過點分配后處理過程檢查串擾約束滿足情況，對違反約束的線網對進行拆除，放入后續線網隊列進行重新分配.實驗數據表明，該演算法能夠取得好的效果 -
Abstract : an algorithm to resolve the coupling effect problem is proposed during the cross point assignment ( cpa ) stage. in the algorithm, the priority queue concept and the rip - up and reroute strategy are combined to control crosstalk noise caused by interconnect coupling capacitance. first, the nets are arranged into different priority queues according to their weighted sum of their length and criticality. then, the cpa problem for one queue of nets is translated into a linear assignment problem. after the assignment of one queue of nets, a post - cpa checking routine is performed to check and rip up the net pairs which violate the crosstalk noise constraint and then push them into the next queue to be reassigned. the algorithm is tested by a set of bench mark examples, and the experimental results are promising
文摘:提出了一種在過點分配階段解決噪聲耦合效應問題的演算法.該演算法採用優先隊列同拆線重布策略相結合的方法，控制由互連線耦合電容引起的串擾噪聲.演算法中，首先按照線長和約束限制，將線網劃分到若干個優先隊列中.然後，將每個優先隊列的過點分配問題轉換為線性分配問題.在完成一個線網隊列的分配后，通過過點分配后處理過程檢查串擾約束滿足情況，對違反約束的線網對進行拆除，放入后續線網隊列進行重新分配.實驗數據表明，該演算法能夠取得好的效果 -
The dissertation analyses the timing effect of ir drop, and gives the expression for the timing effect ; and the dissertation analyses the crosstalk effect of cell internal routing, presents a cell internal routing algorithm for crosstalk minimization and a crosstalk model for timing analysis
論文研究了irdrop對單元時序參數的影響，給出了相應的表示方法；論文研究了單元內布線對串擾效應的影響，提出了一種減小串擾效應的單元內布線演算法和串擾效應的估算模型。 -
However, some improvements have been made for the distributed rc model, the precision ca n ' t attain the request due to the influence of parasitic effect especially the increasing inductance with the development of interconnect technologies in deep - submicrometer region. so these influences must be taken into consideration and the building of new distributed rlc model for interconnect delay and crosstalk becomes more importance. according to this model, two cases, that is, cmos driving transmission line and interconnect line between chips have been analyzed
對傳統的分佈rc模型進行了改善，但隨著互連向深亞微米級發展，寄生效應的影響尤其是電感的影響，必須考慮，因此建立新的rlc傳輸模型是很必要的，本文提出了這種新的互連模型，並對cmos驅動互連線和晶元之間互連兩種情況進行了分析，驗證了延時模型是可靠和精確的，並對延時的改善起到了指導作用。 -
To the pcb, here detailedly introduce all kinds of disturb, sensitive element and the coupling modes of transmit. here mainly analyse the master coupling route ( the trace of the pcb ) and the shield of crust in theory, set up the models of them include the study on the effect of an external electromagnetic interference on a pcb trace, the study on the effect of an hole leak electromagnetic interference on a pcb trace and the study on the crosstalk analysis between two transmission - lines of pcb
詳細介紹了pcb上的電磁兼容原理，對于主要耦合干擾途徑（對pcb上走線的耦合）和pcb的外殼屏蔽進行了詳細的理論分析及推導，對pcb板上微帶線走線的各種耦合情況和外殼屏蔽進行了建模，包括外電磁場對走線的耦合、孔縫泄漏場對走線的耦合、走線之間的串擾等情況。
分享友人