cylinder lubrication 中文意思是什麼

cylinder lubrication 解釋
氣缸潤滑
  • cylinder : n 1 圓筒；機筒；烘筒；量筒；（印刷機等的）滾筒。2 【數學】柱（面），柱體。3 【機械工程】汽缸；【...
  • lubrication : n. 潤滑，油潤，上油；潤滑作用。 lubrication groove 油槽。 ring lubrication油環潤滑法。
  1. Ma yan ? ying, liu jia ? qi. experimental investigation of oil film of port plate / cylinder block in axial piston pump j. lubrication engineering, 1999, 3 : 3539

    鄭煒， ?有雄，魯寶香.軸向柱塞泵配流副油膜的實驗研究j .潤滑與密封， 1995 ， 5 ： 3739
  2. It concludes that the availability and the operating efficiency of the cylinder stone scrubber are enhanced so long as the insufficiency of its vibration and chain lubrication is solved

    通過解決圓筒洗石機振動和鏈條潤滑不充分等關鍵缺陷問題后提高了設備的利用率和運行效率，發揮了圓筒洗石機的效能。
  3. Upper cylinder lubrication

    氣缸上部潤滑
  4. Cylinder lubrication cock

    汽缸潤滑旋塞
  5. Texas texmarine 700 is suitable for cylinder lubrication of engines burning high and very high sulfur content residual fuel oils

    本產品適用於：以高含硫及特高含硫的渣油作為燃料的柴油機汽缸潤滑。
  6. The worm - drive is widely used in modern industry, especially the ordinary cylinder worm - drive in machine tool manufacturing sector. main disadvantages of worm dives are lubrication and wear problems due to relatively high sliding at the tooth contacts. the ordinary cylinder worm - drive has almost become an exclusive selection in general low speed transmission work - platform and continuous graduation mechanism

    蝸桿傳動具有傳動比大、體積小、運轉平穩、噪音小等特點，在現代工業中應用非常廣泛，在機床製造業中，普通圓柱蝸桿傳動的應用尤為普遍，並且幾乎成了一般低速傳動工作臺和連續分度機構的唯一傳動形式。
  7. Scuffing failure of piston ring - cylinder liner in liquid - solid lubrication

    自潤滑軸承在煉鐵廠托輥中應用的試驗研究
  8. Four cylinder, horizontally opposed, air cooled, two cycle engine, with solid state magneto, mixture lubrication. suitable for pusher and tractor installations

    四缸，水平對置，風冷，兩沖程，磁電機，混合潤滑.適合於推式或拉式安裝
  9. Based on reynolds equation and solid particles carrying model, a theoretical model for piston ring - cylinder liner lubrication in liquid - solid lubrication had been proposed. the effect of solid particles " diameter and concentration are introduced in the model. the influence of the particles " diameter and concentration on load, film thickness and friction force had been analyzed

    基於reynolds方程及顆粒承載模型，引入顆粒直徑、濃度等參數，並建立了分析液固二相潤滑下活塞環?缸套摩擦副潤滑狀態的模型，探討了不同顆粒直徑和濃度對承載、油膜厚度及摩擦力的影響。
  10. Based on an experiment performed on the piston ring - cylinder bore wear tester, liquid - solid lubrication is investigated in this thesis. the wear of the samples under different lubrication conditions ( the solid concentrations are 0 %, 0. 02 % and 0. 1 % by weight ) are discussed. the variations of the surface topography, especially the statistical parameters and functional parameters are studied, and the reasons that cause the variations are analysed

    本研究基於活塞環-缸套摩擦磨損臺架實驗研究了液-固二相流體潤滑的問題，探討了潤滑油中不含固體顆粒、含有0 . 02和0 . 1納米顆粒三種潤滑狀態下的磨損情況，並進一步研究了液-固二相流體潤滑狀態下試件表面形貌特性的變化，主要是統計參數和功能參數的變化，並探討了引起變化的原因，為更深入的液-固二相流體潤滑問題的研究以及表面形貌設計提供理論上的參考。
  11. The signal processing software was developed by vc + + tools. the modules of the software including board controlling, signal input, data saving, figure display, statistic computing, filter design, spectrum analysis, etc. based on the experiment performed on the piston ring - cylinder bore wear tester, the friction force and max scuffing load under different liquid - solid lubrication ( the solid concentrations are 0 %, 0. 02 % and 0. 1 % by weight, the type of particles are mos2 and udp ) is investigated in this thesis

    然後，以內燃機中的活塞環-缸套摩擦副為目標，在活塞環-缸套摩擦副實驗臺架上進行模擬實驗，考察在不同二相流潤滑（潤滑油分別為純潤滑油、含納米級金剛石粉（ udp ） 、二硫化鉬粉（ mos _ 2 ）的濃度為0 . 02和0 . 1的液-固二相潤滑油）條件下摩擦副的摩擦力及極限擦傷載荷的變化。
  12. The oil is thrown upward as droplets or fine mist and provides adequate lubrication to valve mechamisms, piston pins, cylinder walls, and piston rings

    飛濺上來的油形成油滴或油舞，使氣門機構，活塞銷，汽缸壁和活塞環得到充分的潤滑
  13. Numerical calculation for the lubrication pressure of the piston and cylinder tribopairs

    缸體間油膜潤滑壓力的數值計算
分享友人
分享到 Line

分享到臉書