damping error 中文意思是什麼
damping error
解釋
沖擊阻尼誤差-
This method is especially accurate in damping identification with the relative error less than 1 % to theoretic values
尤其在阻尼比的識別上，相對誤差在1 %以下。 -
On schuler-tuned compasses this error is avoided by cutting out damping during changes in speed and course.
在休拉調諧羅盤中，這項誤差由於在速度、航向改變時切斷阻尼而避免。 -
The mode superposition method, based on equivalent linearization and forcing decoupling method of non - classical damping matrix of energy dissipation systems, is the just one. at the same time, iterative process will increase computing workload and forcing decoupling method increase error
基於等效線性化的強行解耦振型分解法在一定程度上符合此要求，但此方法存在著迭代計算工作量大、強行解耦增大計算誤差的不足。 -
The first - order perturbation method correct for forcing decoupling method based on perturbation theory is put forward to decrease error ; iii. the complex modal method is introduced into analysis of non - classical damping systems to eliminate error of forcing decoupling method, and improve the complex modal response spectrum, which can apply to design of non - classical damping systems ; iv. for exerting the energy dissipation capability of each device, a two - step optimum method, whose controlling function is extremum expectation of interbedded displacement, is put forward to optimize the number and position of device ; v. the problem of iterative method applied to analyze energy dissipation systems is indicate, and give some primary advice based on pilot study
為改善上述缺點，本文進行了以下的研究工作：在忽略耗能器附加質量的基礎上，推導出適用於耗能減震結構的攝動法，減少振型分解法在迭代計算過程中的工作量，加快計算速度；針對運動方程的強行解耦所產生的誤差，根據攝動法原理，對其進行一階攝動修正；為消除強行解耦振型分解法用於非比例阻尼結構分析時產生的誤差，引入狀態空間對系統進行復模態分析，並改進了基於復模態理論的、適用於非比例阻尼結構設計的雙反應譜方法；對于耗能器的數量和位置優化進行了一些探討和研究。 -
This thesis discusses detailedly the flow process of ip multicast, error discovery method and error recovery method, and also proposes a new error control method to implement reliable multicast in computer supported cooperative design system : serial integrates with timer are used to discover error, arq mechanism based on nak feedback is modified to correct error, " sliding window " mechanism is imported to make up the drawbacks of traditional nak, and " slotting and damping " technique is used to resolve the question of " feedback implosion " which results from multicast reliability control
詳細研究了ip多播傳輸的流程、數據傳輸的差錯檢測方法及差錯恢復方法，提出在協同設計系統中實現可靠多播的控制方法：利用序列號和計時器相結合的方法進行傳輸數據的差錯檢測，改進了基於nak反饋信息的arq重傳機制來實現差錯恢復，並引入了滑動窗口機制來解決傳統nak方法的不足，採用「時間分槽?抑制」技術來解決由於進行多播可靠控制而產生的「反饋內陷」問題。
分享友人