design prototyping technique 中文意思是什麼

design prototyping technique 解釋
原型設計技術
  • design : vt 1 計劃，企圖，立意要…。2 指定，預定；留給，留著。3 設計，草擬，擬定，籌劃；起草，畫草圖，打（...
  • prototyping : （原型）：數據庫的應用程序生命周期的一個階段，包括勾踐數據庫應用程序的工作模型。
  • technique : n. 1. （專門）技術；（藝術上的）技巧，技能。2. 手法〈如畫法，演奏法等〉。3. 方法。
  1. Eight trapezoid labyrinth flow - channels are designed through modification to the cell dimension and the number of flow cells based on the parameterized structural design. integral emitter prototypes combining exterior hull and exterior flow - channel are built using rapid prototyping technique, and structural dimension of those flow - channel are measured by optical microscope, the measuring results showed that the design can completely meet the requirement of emitter accuracy

    文中以參數化的設計思想，通過改變梯形迷宮流道單元尺寸和單元數設計了8種梯形迷宮流道，採用快速成形技術製作出外管與內迷宮流道一體化的滴頭原型；利用最小標注尺寸為50nm的光學顯微系統對滴頭流道結構尺寸進行了測量，分析結果顯示流道尺寸精度完全滿足滴頭的製作要求。
  2. Applying the key technique of concurrent engineering - design for function ( dff ), design for assembly ( dfa ) and design for manufacture ( dfm ) of the method of design for " x ", the virtual design of the torque converter is accomplished in catia v5. then the model constitution and the simulation of virtual process of the torque converter is done in catia v5, including the model constitution and the simulation of 5 - aixe nc virtual process of the vane, the model constitution ( material : pvc ) of the idler pulley rapid prototyping ( rp ) and the virtual assembly and the motion simulation of the torque converter, etc. 3 - d data exchange between various cad systems is realized by using step standard. the lever of classing the character model of the torque converter is given

    應用并行工程的關鍵技術之一? ?面向產品全生命周期的設計dfx中面向功能的設計dff 、面向裝配的設計dfa和面向製造的設計dfm的方法，在catiav5中完成液力變矩器虛擬設計；在catiav5中對液力變矩器進行虛擬加工建模和模擬，包括液力變矩器導輪葉片五軸數控加工刀軌建模與模擬、導輪快速成型rp建模（ pvc材料） 、液力變矩器虛擬裝配和運動模擬等；採用step標準實現多cad系統之間三維數據交換，提出液力變矩器特徵模型的分級標準並對三維模型數據進行分級管理，制定相應的權限等級以規范合作廠家的產品數據管理層次。
  3. The best technique for analog prototyping is to use a prototype of the final pcb - certainly no design is complete until the final pcb layout has been proved to give the required performance

    對模擬電路而言，最佳的搭試平臺莫過于用「定型」的pcb作原型了，顯然這是個悖論，因為只有電路達到規定的性能指標，電路設計才算定型，設計才算結束。
分享友人
分享到 Line

分享到臉書