diameter of movement 中文意思是什麼
diameter of movement
解釋
機心直徑, 結構直徑-
The subsequent southeastward movement of the hailstorm brought hailstones of diameter up to 2. 5 cm to most parts of kowloon later that afternoon
這雹暴其後向東南方移動，在下午較后時間為九龍大部份地區帶來直徑達2 -
Considering different soil spring models for vertical fault movement and horizontal fault movement, two damage cases of pe pipeline in ji - ji earthquake have also been simulated. the large deformation of a buried pipeline under fault movement is investigated in the 4th chapter. to examine the inelastic behavior of buried pipelines, the parametric studies on pipe material property, diameter ( d ), diameter - to - thickness ratio ( d / t ), crossing angle ( ), as well as soil stiffness, have been conducted using a shell - spring fem method
對於0 p三90 」的情況，當斷層位移相對管徑還不是很大時（管子內的彎曲應變與軸向拉伸應變相差不大的情況） ，斷層附近管子變形形式與梁相似；當斷層位移相對管徑很大時（管子以軸向拉伸應變為主的情況） ，斷層附近的管子軸線變形為一圓弧，管子表現得像一條沒有彎曲剛度的索。 -
When the transportation load is long - term evenly distributed, the influences of each relevant factor, i. e. pipeline depth, diameter, deformation module of foundation, poisson ratio of soil and tyre pressure of vehicles, toward mises stress and vertical displacement of pipelines are discussed. when the transportation load is movable and invariable, the changing rules of mises stress and vertical displacement during the vehicle ' s movement are calculated and analyzed, and effects of vehicle velocity and tyre pressure toward these two mechanical characteristics are discussed. when the transportation load is stable and simple harmonic, the changing rules of mises stress and vertical displacement during the time of load function are calculated and analyzed, and effects of vehicle velocity and tyre pressure toward these two mechanical characteristics are also discussed. in three - dimensional analysis, mises stress and vertical displacement of pipelines under three kinds of transportation loads are calculated, and the analysis and discussion of correlative factors are also made
當交通荷載為長期均布荷載時，討論了各相關因素，包括管道埋深、管徑、地基變形模量、地基泊松比和車輛輪壓大小分別對管道mises應力和豎向位移的影響；當交通荷載為移動恆載時，計算並分析了車輛行駛過程中管道mises應力和豎向位移的變化規律，討論了車速和車輛輪壓對這兩個管道力學性狀的影響；當交通荷載為穩態簡諧荷載時，計算並分析了荷載作用時間內管道mises應力和豎向位移的變化規律，討論了車速和車輛輪壓對管道力學性狀的影響。 -
According to the principle of curve axial symmetry, authors inferred the theoretical foundation of error - free translation of the working equipment of loader and proved that when the diameter of piston rod on arm oil cylinder was designed properly, the two oil cylinders could be guaranteed to have a synchronous movement which made the bucket maintain translation throughout the working process under the condition of the oil cylinder ' s basic parameter ; also made the equipment structure of the loader greatly simplified and provided the reference for improvement of the present equipment of loader
根據曲線軸對稱原理，推導出了能使裝載機工作裝置無誤差平移的理論基礎，證明了只要適當地設計動臂油缸活塞桿直徑，就可以在油缸的基本參數上保證機構工作時兩油缸同步運動，使鏟斗在作業過程中保持平移；使裝載機工作裝置結構大為簡化，為進一步改進現有裝載機工作裝置提供參考。 -
Aimed at the equal - diameter cam mechanism with follower of planar movement, and according to two conditions of existing meaningful solution of the mechanism and of ensuring transmission angle of output swinging rod, the value selection ranges of cam motion angle, of swinging angle of out - put swinging rod and of its primary installation angle were analyzed and determined, and then proceed to plot the region graph of selectable value for motion angle of cam and swinging angle of swinging rod, thus provided convenience for the design and employment of that mechanism
摘要針對平面運動從動件等徑凸輪機構，根據機構存在有意義解和保證輸出擺桿傳動角兩個條件，分析並確定了凸輪運動角、輸出擺桿擺角及其初始安裝角的取值范圍，進而繪制了凸輪運動角與擺桿擺角的可選值域圖，為該機構的設計與使用提供了方便。 -
Wheel diameter is based mainly from 254mm to 510mm, suitable for a diameter process of general - precision core shaft. main work piece can be grinded right left crossing movement fixed direct - feed and fixed beveled angle
砂輪直徑以254 510為主，適用一般精密芯軸外徑加工，主要加工物可做左右橫送式移動研磨固定式直送研磨及固定式斜角度研磨。 -
It ` s suitable for the bend and deformation of the metal plates and it can roll the round and arcshapes and the cone ones within its specified ranges. it has the function of prebending the plate at both ends. the two lower rollers are the driving ones and can make the horizontal movement ; and the upper is a driven one and can make the up and down movement. the moving manner includes the mechanical and industry, boilers, shipbuilding, metal structure, machine manufacture and other trades, especially for the roll the steel trunks with smaller diameter and longer length in power transmission and trandform and other trades
該機適用於金屬板材的彎曲成型，可卷制圓形，弧形和一定范圍的錐形工作，並有板材端部預彎功能，本機型兩個下輥為主動輥並可水平移動，上輥為從動輥上下移動，移動形式有機械式和液壓式，傳動軸均採用萬向連軸器連接，它廣泛適應于石油化工鍋爐造船金屬結構及機械製造行業，特別適用於送變電行業等直徑較小長度較長鋼管桿的卷制
分享友人