dynamic calibration system 中文意思是什麼

dynamic calibration system 解釋
動態校準系統
  • dynamic : adj 1 動力的，動力學的；力學（上）的；動（態）的；起動的。2 有力的，有生氣的；能動的；（工作）效...
  • calibration : n. 1. 測定口徑。2. 刻度，標度，劃度數。3. 校準；標準化。
  • system : n 1 體系，系統；分類法；組織；設備，裝置。2 方式；方法；作業方法。3 制度；主義。4 次序，規律。5 ...
  1. Angular calibration of radar antenna system is composed of the calibration of angular error sensitivities ( also called directional sensitivity ), adjustment of cross - coupling of azimuth and elevation signals, and the calibrations of system errors such as antenna axial system error, dynamic delay and so on

    雷達系統天線的角度標校包括對系統角誤差靈敏度（又稱定向靈敏度）的標定、方位俯仰信號交叉耦合的調整以及對天線軸系誤差、動態滯后等系統誤差的標定。
  2. Using the system designed in this thesis work, flow field calibration of the wind tunnel is accomplished, which covers dynamic pressure drop coefficient, dynamic pressure time stability, axial static pressure gradient, boundary layer, and degree of turbulence, etc. boundary layer measuring principle and method are especially described in detail, the relationship between boundary layer thickness, wind speed setting, and the depth of the experimental section is summarized, and finally the calibration data for th e model center zone under specific wind speed are given

    然後利用本文設計的系統完成了落差系數、動壓時間穩定姓、軸向靜壓梯度、邊界層及湍流度等內容的流場校測。特別對邊界層測量的原理及方法做了較詳盡的敘述，總結出邊界層厚度與設定風速、實驗段深度的關系，然後給出模型中心區一定風速下校正數值。
  3. In our country the method of pressure - measuring with copper cylinders adopts the system of static calibration on the whole. the serious static - dynamic discrepancy will be caused when the copper cylinders statically calibrated are used to measure the dynamic chamber pressure

    我國的銅柱測壓法基本上仍沿用靜態標定體制，而靜標銅柱用於動態膛壓測量會產生嚴重的靜動差。
  4. Pneumatic dynamic snaking calibration system

    氣動式動態蛇行校正系統。
  5. Test analysis of the laser ' s response time in the transient dynamic calibration system of high - temperature transducer

    高溫傳感器動態校準系統中激光器響應時間的測試分析
  6. The reliability of measurement system is redefined, and new methods are presented to evaluate the reliability, the calibration and verification period using dynamic uncertainty based on the analysis stated above and the characteristic of measurement systemquantum transformation, which makes the separation actuality of quantum analysis and reliability analysis of measurement system to an end

    基於前面的分析及測量系統進行量值傳遞的特點，對測量系統的可靠性重新進行了定義，提出了採用動態不確定度對測量系統的可靠度、校準或檢定周期進行評價的新方法，從而結束了目前測量系統量值分析與可靠性分析脫離的現狀。
  7. 6. since the monitor precision of quasi - dynamic calibration system is very important, the model of the four channel electric pressure - measuring system in frequency domain is built up. the cause of variance is analyzed. the error function of the system is defined and the formula of correcting the system error is derived

    6由於落錘液壓動標裝置校準系統的校準壓力監測精度極為重要，本文對四路電測壓力系統進行頻域建模，分析了產生不一致的原因，定義了系統的誤差函數及推導了統一誤差模型的修正公式。
  8. Auto - calibration system for transient surface temperature dynamic characteristics

    瞬態表面溫度自動動態校準系統
  9. Methods based on statistics for dimensional position and data processing were suggested for the calibration of the dimensional angle shown by a programmable dynamic target using linear matrix ccd and video interpretation. studies in this paper show that the programmable target system is functional and capable of testing photoelectric theodolite. consequently conclusions can be drawn that programmable dynamic target is new equipment to tes t photoelectric theodolite, not only can it check and test the performance, but also can measure the precision

    得出了初步結論：可編程動態靶標由於配置了位置輸出元件和時間統一系統，實現了位置閉合，能對靶標的運動進行有規律的控制，克服了常規旋轉靶標的固有缺點，可以提供模擬目標的空間標準角，因此可編程動態靶標不僅可以作為跟蹤靶標使用，還可以作為測量靶標使用，是檢測光電經緯儀跟蹤性能和測角精度的新裝置。
  10. To make the quasi - dynamic calibration system perfect, much work has been done in this dissertation. the main work consists of the following parts

    本文基於進一步完善準動態校準技術，為建立完善的塑性測壓器材的準動態校準體制的考慮，進行了大量的工作。
  11. Meanwhile, the paper also gives a more detailed discussion about the key techniques related to dynamic tracking measurement, such as : the measuring principle and method, establishment principle of the virtual coordinate system, self - calibration principle, the redundancy design and allocation principle, etc

    並且介紹了測量的原理、原則、方法和虛擬坐標系的建立以及冗餘測量配置與測量方法、測量系統的自標定、實用測量系統的技術特點等。
分享友人
分享到 Line

分享到臉書