erection stress 中文意思是什麼
erection stress
解釋
安裝應力-
Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating
箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。 -
D finite element local analysis is done for hv porcelain post insulator by abaqus finite element software. the stress distribution of one - piece structure under dead weight, erection deviation, temperature change, wind load and short - circuited load is analyzed, which provides the scientific basis for security assessment of post insulator
以高壓瓷瓶支柱絕緣子為研究對象，採用abaqus有限元軟體進行三維有限元局部分析，分析了整體結構在自重、安裝偏差、溫度變化、風載以及短路電流載荷作用下的應力分佈，為支柱絕緣子的安全性評定提供了科學的依據。 -
Aiming at main project of the xiaoxihu bridge, a low pylon cable - stayed bridge, based on the existing theory and method of the bridge construction controlling theory, using the basic function of " ansys ", farther exploitation was done on concrete elasticity and creep calculating distinguishingly, nonlinearity analysis theory was used to construct the space model, the main beam, string pylon and abutment were simulated by the beam elements which was considered the shearing effect. which is worthy of considering that using the geometric non - linear truss elements to simulate the stayed - cable, form traveler is modeled as structure elements and participate in stress analysis. four stages are used to model the construction stage, which are : ( 1 ) the erection of form traveler ; ( 2 ) placing the segmental concrete ; ( 3 ) jacking the tendons ; ( 4 ) tensioning the stay cables
針對建設中的小西湖矮塔斜拉橋的主體工程，結合已有的橋梁施工控制的理論和方法，利用大型通用計算軟體ansys的基本功能，並著重在混凝土彈性計算及徐變計算方面做了相應的二次開發，採用非線性分析理論並建立了空間結構模型、用考慮剪切作用的梁單元模擬主梁、索塔和橋墩；用可考慮幾何非線性的桁元模擬斜拉索、施工掛藍作為結構單元進行拆裝，參與受力計算，整個施工過程按施工循環周期分為若干階段，每個階段又分為四個工況，即：空掛藍就位、澆築完畢階段混凝土、張拉預應力鋼筋和張拉斜拉索。 -
This paper emphasizes on the construction control of concrete arch bridge, which is constructed by the precast segmental cantilever method. through analyzing this new erection method, it is considered that the cable forces directly influence the stresses of arch rib sections and the deflections of the arch axis, in addition, the stress of the arch rib section is the key factor in construction control
本文以懸臂拼裝鋼筋混凝土拱橋的施工控制為研究對象，結合工程實例，分析了大跨徑鋼筋混凝土拱橋的懸臂拼裝施工方法，認為施工過程中拉索的索力直接影響拱肋截面的應力和拱肋軸線的標高，拱肋截面的應力是懸臂拼裝拱橋施工控制的關鍵因素。
分享友人