feed water analysis 中文意思是什麼
feed water analysis
解釋
給水分析-
Under the appropriate conditions of sampling equipment of gas chromatographic headspace analysis, determine a suitable salt and a suitable extracting solvent by the orthogonal design method, then determine the fitting feed composition of ethanol - water mixture, the fitting distribution between extracting solvent and mixture, and the fitting salt concentration by the uniform design method
在對建立的頂空氣相色譜采樣裝置的操作條件進行優化之後，先用正交試驗設計法確定非連續性因素鹽和萃取劑及其在備選水平中的適宜水平，再用均勻試驗設計確定連續性因素乙醇的進料濃度、萃取劑配比和加鹽量及其備選水平中適宜的水平范圍。 -
Performance test and analysis of boiler feed water pumps before and after overhaul
給水泵大修前後性能試驗及分析 -
Establishing on the foundation of the project of " the monitoring state and maintenance assist support system of feed pump for 300mw unit, shiheng power plant, shandong ", this paper ' s content comprise on - line monitoring and thermodynamic calculation on small steam turbine for feed water pump, and supply the necessary data for feed water pump ' s performance analysis, trouble analysis and small steam turbine ' s performance analysis, optimization, heat stress calculation and tremble monitoring
=本論文的內容是建立在「山東石橫電廠給水泵狀態監測與維修輔助支持系統」項目基礎上，涉及大型機組鍋爐給水泵驅動用小汽輪機進行在線監測和熱力計算，為給水泵的性能分析、故障分析以及小汽輪機的性能分析和優化、熱應力計算和震動監測提供必需的數據。 -
A test - bed of dg45 - 80 10 hypo - pressure feed water pump is designed, based on which the general on - line performance testing system is developed and the thermodynamic method is introduced to measure the efficiency of the pump. a new programming technology combining vc + + with matlab is presented by which the vibration monitoring system of boiler feed water pump is developed successfully to perform data analysis after on - line acquisition
本文首先進行了次高壓鍋爐給水泵dg45 80 10實驗臺的設計，在此實驗臺設計成功並安裝調試通過的基礎上，開發了鍋爐給水泵通用性能試驗系統，包括測點的布置、各型測量儀器的選購，設計，安裝和調試以及軟體平臺開發。 -
Abstract : this paper apply asme & quot; feed water pump npsh analysis during load rejection & quot; theory to check bfp npsh of zhuhai power plant 700mw units in the condition of vwo and also confirm the calculating result by load rejection test
文摘:利用asme的「甩負荷時給水泵汽蝕余量的分析」理論，校核了珠海電廠容量700mw機組在最惡劣工況即閥全開跳機工況時的給水泵汽蝕余量，並在甩負荷時，進行了試驗驗證。 -
Through analysis of test data in the field, it shows that the main causes leading to said phenomenon for are : adding water - cooling panel in the furnace ; rising of the feed - water temperature ; and somewhat smaller air flow rate in operation
通過對其現場測試數據的分析表明，爐內增加水冷屏、給水溫度升高以及運行風量偏小是造成其主蒸汽溫度偏低的主要原因。
分享友人