filling gate 中文意思是什麼
filling gate
解釋
注水門-
It can make the smallest gate mark thar is used for the best plan with strict surface requirements and good products function. it can enlarge the injection quantity and improve the filling speed, it applies to almost the all of plastic materials
能做到最小膠口痕跡，是應用於嚴格表面要求達到高產品性能的最佳方案，能擴大注塑量提高注塑速度，適于各種塑膠。 -
The operation measures for controlling over - filling ( over - emptying ) are feasible ; the hoisting loads of valve and miter gate are less than their design values respectively ; but, there exists cavitation phenomenon needed to pay attention to the first crossover culvert when the value is near and after whole opening
控制超灌（泄）操作方式可行；閥門、人字門啟閉力均小於設計值；閥門接近全開至全開后，輸水廊道第一分流口有空化現象。 -
Find the law of the influence from the injection pressure to the filling time and the cavity pressure and make certain of the best filling time, injection time and injection pressure. though the analysis of the flowing velocity and pressure spread of the key position element in the injection parts in different gate position, we forecast the injection parts quality and the possibility injection flaw and its position, optimize the gate position. in this paper, though the research of analogue of the runner system of metal - powder injection molding and the process of injection molding, we get the law of how the injection parameter influence the injection process
在相同的注射條件下，通過分析喂料在不同直徑和長度流道中的流動規律，得到了喂料在流道中的速度場、壓力場和溫度場，找到了流道長徑比的合理取值范圍，並得出通過改變流道設計可實現對現有設備資源充分利用的結論；給出了不同注射壓力下，型腔壓力與充模時間關系曲線和喂料熔體平均充填速度與充模時間關系的曲線，得到了注射壓力對充填時間和型腔壓力的影響規律，確定了最佳的充模時間、注射時間和注射壓力；通過分析採用不同位置澆口注射時注射件關鍵位置單元的流動速度和壓力分佈，預測了注射件的成形質量，或可能產生的注射缺陷及位置，優化了澆口設置。 -
As alpatitch was driving out of the gate, he saw about a dozen soldiers in loud conversation in ferapontovs open shop. they were filling their bags and knapsacks with wheaten flour and sunflower seeds
阿爾帕特奇從大門出來坐上車走時，看到費拉蓬托夫敞開的店裡有十來個士兵，一面大聲說話，一面把麵粉和葵花子裝進口袋和背包。 -
Criterion of water filling valve series for hydraulic steel gate
水工鋼閘門系列標準.充水閥 -
When building permanent dams and sluice gate structure on navigable or bamboo and log rafting streams, the construction unit must simultaneously build facilities for ship or log passage or, after being approved by departments authorized by the state council, take other remedial measures and also make adequate arrangements for navigation and bamboo and log rafting during the construction period and the initial filling period, and bear the expenses thereby incurred
在通航或者竹木流放的河流上修建永久性攔河閘壩，建設單位必須同時修建過船、過木設施，或者經國務院授權的部門批準採取其他補救措施，並妥善安排施工和蓄水期間的航運和竹木流放，所需費用由建設單位負擔。 -
Mould flow and simulation should be carried out for the best gate location, filling analysis, pressure distribution and heat distribution
適宜應用模擬的模具注塑過程，注射分析、壓力分佈及溫度分佈以確定最佳入水位置、流道尺寸和疏氣位置等。
分享友人