flow parameter 中文意思是什麼
flow parameter
解釋
憐參數-
Using the hulscher model of the formation of sand waves and sandbanks, under the ancient bathymetry, or under the modern bathymetry, the stokes number of the tidal flow and resistance parameter in the radial sandbanks satisfy the conditions for the formation of sandbanks. the research demonstrates that the dynamic flow conditions result in the development of tidal current sandbank. the radial sandbanks and it ' s asymmetrical distributions will still maintain in the future
應用hulscher沙波及沙脊增長模式，通過對該海域斯托克斯數及底部阻力參數的計算首次發現，南黃海輻射沙脊群海域在概化古地形和現代輻射狀沙脊群水下地形情況下，其斯托克斯數及底部阻力參數均滿足形成潮流沙脊的條件。 -
The paper mainly consider the followings : the performance parameter determination of cryopump, heat load determination and heat transfer of large cryopanel, reasonable distribution of heat load, the condition for construct steady flow in small vertical circle pipeline, balance condition for gas and liquid two - phase flow in the connection pipe between cryopanel and dewar, the safety of cryopump
文中探討了低溫泵性能參數的確定；大抽速低溫抽氣面的熱負載的確定及合理分配；冷凝面上豎直圓管內受熱建立穩定流動的條件；冷凝面與杜瓦間的連接管道內氣液「雙相流動」的平衡條件；低溫泵系統運行的安全問題。 -
Numerical calculative simulation could factually reflect the dynamic characteristics of the whole equipment and inner flow and diathermancy of split - stirling crycooler. through the calculation, the velocity, temperature, pressure and other detailed information of airflow in any position inner the crycooler could be gained ; the distribution of each parameter could be confirmed and reasonable explanation for the experiment result could be made
數值計算模擬能接近真實地反映分置式斯特林製冷機的整機和內部流動、傳熱的動態特性，通過計算可以得到製冷機內部任一位置的氣流流動的速度、溫度、壓力等詳細信息，確定各參數的分佈情況，並可以對實驗結果做出合理的解釋。 -
Following this algorithm, the base flow can be calcu - lated from the observed discharge as follows : 1, 22bbqiqiqi where i is the time step in the discharge records, qb is the base flow, q is the total runoff, and is the re - cession constant during periods with no surface runoff. the parameter can be determined through a dis - charge recession analysis
地下徑流的推算公式如下1 1 . 22bbqiqiqi ? ? ? ? 26其中i表示推算的時間步數， qb是地下徑流， q是總的徑流.表示沒有降水時候流量消退系數，可以通過沒有降水時候的流量消退資料推算出出來 -
Second, the paper in - depth discuss the reinforce foundation operation mechanism of technique of composite grouting, including spray incise action of high pressure spray flow to soil, mill metathesis concretion action, and penetrate, split, crush action of serum to soil, etc. third, the paper in - depth study design calculate of composite grouting, design of composite grouting technic parameter
其次，本文對復合注漿法加固地基的作用機理進行了深入的探討，包括高壓噴射流對土體的噴射切割作用、漿液與土的攪拌置換固結作用以及漿液對土體的滲透、劈裂、擠密作用等問題。第三，本文對復合注漿的設計計算、注漿技術參數的設計進行了深入的研究。 -
To calculate this boundary parameter, mohorovicic discontinuity palaeo - heat flow value during basin evolution process is identified through geotectonic background analogy method based on " peeling " method model, and the basin basement palaeo - heat flow is calculated through inversion from today to antiquity with current tectonic structure as constraint condition for palaeo - crustal architecture analogy
為了求取這個邊界參數，以「剝層」法模型為基礎，通過大地構造背景類比法確定盆地演化過程中莫霍面古熱流值，以現今地殼結構為約束條件類比古地殼結構，從今至古反演求取了盆地基底的古熱流。 -
Second, it presents the project design of an astronauts ’ kinetic measurement system that can precisely measure the forces and moments of key points on motorial person. it presents a principle and flow of the project design of an astronauts ’ kinetic measurement system. and it particularly discusses the demarcate of camera system, the gathering and storage of experiment pictures, pick - up of the symbol data, the parameter calculating method of target movement, and the general design of assistant equipment
然後給出航天員作用力測量實驗系統的設計方案，該系統能夠克服重力影響，較精確地得出運動時人體各關鍵點產生的力和力矩;給出了航天員運動參數測量實驗系統的原理及流程，並詳細論述了攝像系統標定，實驗圖像的採集與存儲，標志點數據的提取及目標運動參數解算的方法;給出了輔助設備的概要設計。 -
Ultrasonic has being attracted much attention gradually in fuel atomization because of some specialities of cavitation and infection on liquid flow. in the course of atomization of pitchy oil, especially, does it show greatly its advantage, but its material atomizational mechanism need research ulteriorly. the primary content of this thesis is about adding cantilever reed to effervescent atomizer so as to combine ultrasonic and effervescent. this thesis has discussed ultrasonic some mechanism, ultrasonic dynamical procreator, effervescent and liquid mucosity infection on atomization, at the some time we make some experiments and discuss atomization rule following some machinery parameter and run parameter so as to find some rule about ultrasonic atomization and to rich the research of ultrasonic atomization mechanism. all that will be beneficial to the design about ultrasonic atomization atomizer
超聲波由於其空化機理及對液體的流變性影響等特性，在燃油霧化燃燒中逐步引起人們的重視，尤其在重渣油等高粘度液體的霧化過程中逐步顯示出其優越性，但其具體的霧化機理還需要做進一步的研究在氣泡霧化噴嘴基礎加入懸臂式簧片哨，將超聲波與氣泡霧化相結合是本文討論的主要內容本文從研究超聲波的一些機理入手，討論了超聲動力發生器氣泡霧化以及液體粘度對霧化質量的影響，並通過具體的實驗，根據實驗數據來討論霧化質量隨各種結構參數運行參數的變化規律，以便找到超聲霧化的一些規律，豐富對超聲霧化機理的研究，對超聲霧化噴嘴的設計具有一定的指導意義。 -
According to the above theories, with using the software - deform - 3d, we have made the numerical analog simulation and analyse the warm extrusion forming technique process for sway oil pump stator, optimized the forming : technique and the die parameter for the pockety wall thickness forging this paper concretely analysis and research metal flow ' s characterize in different forming processes
本課題根據上述理論，利用有限元數值模擬模擬軟體deform - 3d ，對轉向油泵定子溫擠成形工藝過程進行模擬模擬分析，優化了油泵定子的成形工藝及模具參數。 -
4 ) in a pre - swirl rotator - stator cavities with discrete pre - swirl nozzles and blade - cooling entry holes, the influences of pre - swirl angle and flow parameter on the flow and heat transfer characteristics were numerically investigated. the correlation for average nusselt number vs rotating reynold number or non - dimensional mass flowrate were established. the results show that : advantage of per - swirl inflow is the effect of cooling the blade - cooling entry holes ; pre - swirl inflow increases heat transfer in rotating disk of pre - swirl chamber ; as pre - swirl angle increases, local nusselt number decreases in pre - swirl chamber ; the temperature of stator of inner rotator - stator chamber and per - swirl chamber decreases as rotating reynold number increases ; when the axial mass flowrate maintains constant, heat transfer in the rotating disk of inner rotator - stator cavities does n ' t change as per - swirl mass flowrate increases, while heat transfer in the rotating disk of per - swirl chamber increases ; when the pre - swirl mass flowrate maintains constant, change of the axial mass flowrate has effect on the whole cavity
結果表明，預旋進氣的優點在於增強了葉片冷卻孔附近的對流換熱效果，局部努謝爾數隨預旋角的增大而有所減小；隨旋轉雷諾數的增加，不論是內轉靜腔室還是預旋腔室的靜盤上的溫度都不同程度的降低：當軸向中心進氣質量流量不變時，隨預旋進氣的質量流量增加，內轉靜腔室的轉盤盤面上的換熱基本沒有變化，而預旋腔室的轉盤盤面上的換熱效果增強；當預旋進氣質量流量不變時，軸向中心進氣的質量流量的改變對整個盤腔都有影響。 -
In different in terne die travel, the metal flow characterize in warm extrusion forming processes and the affection for the flow of metal stage which made by the difference between the blank bottom altitude and the axial direction limiting size in warm extrusion forming technique have been analysed we have gotten the equivalent strain field and the velocity field and other field variable that the blank in different in terne die travel and the die travel - load curve. at the same time, we have analyzed the contributing factor for the oil pump stator forming process optimized and achieve thereasonable die parameter for the war m extrusion forming finally, the optimized technics parameters were used into pilot production, then the qualified oil pump stator forging were produced, the analog results were compared with those of pilot production
論文具體分析研究了不同成形工藝過程中金屬流動的特點，並對不同凸模行程下溫擠成形過程中的金屬流動特點、坯料連皮厚度（底部高度）與溫擠壓成形工藝中的軸向界限尺寸的差值對金屬變形階段的影響進行了分析，獲得了坯料在不同凸模行程下的等效應變場、速度場等場變量及凸模行程-載荷曲線，同時對油泵定子成形過程的影響因素等進行了分析，優化並獲得了合理的溫擠成形工藝及模具參數。最後，利用模擬優化獲得的各項工藝參數進行生產實驗，得到實際生產出的合格油泵定子件，並將模擬結果與生產實驗結果進行比較。 -
The flow stress can be described by temperature - compensated strain rate, the so - called zener - hollomon parameter
利用7055鋁合金高溫塑性變形時穩態流變應力、應變速率（ -
In this paper, the sensibility analysis of the factors affecting the temperature in well bore is relatively systematically made by using a large number of the data calculated with the borehole flow and heat transfer 3 ? d numerical model proposed by the author. the study shows that the thermophysical parameters of the drilling fluid and formation, etc. and the entrance temperature and circulating capacity, etc. of drilling fluid have a greater influence on the temperature in well bore. therefore, accurately mastering the thermophysical parameter values of penetrated formation and drilling fluid in well bore, considering the influence of the temperature and pressure on thermophysical parameters and accurately measuring such parameters as entrance temperature and discharge capacity of drilling fluid, etc. are of utmost importance for accurately simulating the temperature in well bore
利用由作者提出的井內流動和傳熱的三維數值模型計算所得的大量數據，文章對影響井內溫度的諸多因素進行了較系統的敏感性分析，研究表明：鉆井液和地層等的熱物理參數以及鉆井液的入口溫度、循環排量等對井內溫度有較大影響，因此，準確掌握所鉆地區地層和井內鉆井液的熱物理參數值，考慮溫度壓力對熱物理參數的影響，準確測量鉆井液的入口溫度、排量等參數值，對于井內溫度的準確模擬至關重要。 -
Relationship between snail lengh of torsion cord and umbilical arterial blood flow parameter and neonate a family - score
臍帶扭轉螺距值及臍動脈血流參數與新生兒阿氏評分的關系 -
Two - phase flow parameter measurement is a difficulty in field of industrial process parameter measurement
兩相流參數檢測是工業過程參數檢測的一個難點。 -
Process tomography technique is an attractive development orientation for the two - phase flow parameter measurement
應用過程層析成像技術進行兩相流參數檢測的研究是一個引人注目的發展方向。 -
The flow through the throat - type energy dissipator and the right - angle energy dissipator are calculated by using the two - equation turbulence model, which is expansively used to simulate the flow field successfully. the principal content and the achievement are concluded as follow : as a kind of internal energy dissipator in which the turbulent flow is contracted and expanded abruptly, throat - type energy dissipator was regarded as one of the potential energy dissipator for its many advantages, such as stable flow pattern, simple structure, easily controllable flow parameter, and anti - cavitation property
結合實體試驗，利用k -模型對當今尚處于起步階段的新型消能方式?洞塞消能工和直彎消能工進行了數值模擬研究，主要內容和研究成果如下： 1洞塞消能作為一種突縮突擴式的內流消能工，具有流態穩定、結構簡單、水流參數易於控制及防空化性能等優點，是一種很有發展潛力的消能方式。 -
This machine used plc programed light controller to control, it is equipped with 6 inches touching screen and stable pressure fixing flow parameter to control the volume by controlling the filling time
本機採用可編程式控制制，配以6英寸觸摸屏人機界面系統，採用常壓式固定流道參數，控制灌料時間來實現不同計量的灌裝。 -
It is equipped with 10. 4 inch touching screen and stable pressure fixing flow parameter to control the volume by controlling the filling time. it is in simple structure and can fit for all sizebottles. when the bottle changed, it is unnecessary to change the parts
本機採用可編程式控制制，配以10 . 4英寸觸摸屏人機界面系統，採用常壓式固定流道參數，控制灌料時間來實現不同計量的灌裝，結構簡單，大小瓶通用，改變瓶形無需更換配件，調整即可。 -
But there are some problems and difficulties in ect designs and ect applications. the topics of this dissertation are small capacitance measurement that is a key part in ect designs and ect applications, high - speed data acquisition system design and ect applications in two - phase flow parameter measurement
本文針對制約電容層析成像技術發展和應用的微弱電容測量和數據採集速度等問題進行了深入研究，研製了一套高速電容層析成像系統並在氣液兩相流流型識別和空隙率測量以及流化床固相含率分佈量化監測上得到成功應用。
分享友人