full-load current 中文意思是什麼

full-load current 解釋
滿載電流
  • full : adj 1 充滿的，裝滿的。2 充分的，豐富的；擠滿的；（吃、喝等）盡興的，3 （精神）飽滿的。4 完全的，...
  • load : n 1 裝載，擔子；負擔；工作（負荷）量。2 （車船等的）裝載量；一馱，一車，一飛機。3 【電、機】（機...
  • current : adj. 1. 通用的，流行的。2. 現在的，現時的，當時的。3. 流暢的；草寫的。n. 1. 水流；氣流；電流。2. 思潮，潮流；趨勢，傾向。3. 進行，過程。
  1. The typical ground current ( quiescent current ) is 1ma at full load, 60 a with no load and, and less than 1 a in shutdown mode

    在滿負載條件下，靜態電流為1ma ;在空載情況下，靜態電流為60 a ;在關斷情況下，靜態電流小於1 a 。
  2. When ordering overload relays, specify horsepower, voltage and full load current per motor nameplate

    訂購過載繼電器時，請註明每臺電機的功率馬力、電壓和滿載電流。
  3. With the “ skip ” modulation technique, quiescent current are reduced to a minimized value of 1ma with full load, 60ua with no load, and less than 0. 01ua in shutdown mode

    在典型情況下，晶元滿載時的靜態電流為1ma ，空載時的靜態電流僅為60ua ，關斷電流小於0 . 01ua 。
  4. It makes finite element analysis for no - load motor, full - load motor and armature magnetic field singly acting motor, and it gets distributing map of magnetic field and static characteristics curve as different rotor angle and different armature current in a permanent magnet circle for the motor, it analyzes and explains influences of armature magnetic field on the inductance characteristics of windings

    分別對電機空載、負載以及電樞磁場單獨作用3種情況下進行了有限元分析，得出在1個永磁磁鏈周期內不同轉子位置角和不同電樞電流作用下的磁場分布圖以及靜態參數特性曲線。
  5. Among them, phase shifted ( ps ) full bridge ( fb ) zero - voltage - switched ( zvs ) pulse - width - modulated ( pwm ) dc / dc converter has strong competitive power in big power capacity fields. but it has some limitations such as smaller load range with zvs and larger circulation energy. the ps - fb - zvs - pwm dc / dc converter with a saturable inductor utilizes saturable inductor s critical saturable current characteristic and storage energy, to enlarge load range with zvs and improve output efficiency under light load

    其中，移相控制零電壓開關脈寬調制dc / dc全橋變換器在大容量領域很有競爭力，但它具有實現零電壓開關負載范圍小，循環能量大等限制，帶飽和電感的移相控制零電壓開關全橋變換器利用飽和電感的臨界飽和電流特性及儲能，來擴大零電壓開關（ zvs ）的負載范圍，提高輕載時的輸出效率，具有非常重要的研究價值。
  6. When start to operate the furnace, raise voltage alowly and gradually, never give full load at one time, or the heating element will be damaged by over current impulse

    爐子在開始通電運行時，要逐步緩慢升壓，不可一次加滿負荷，否則會因沖擊電流過大造成元件損壞。
分享友人
分享到 Line

分享到臉書