gear teeth 中文意思是什麼

gear teeth 解釋
齒輪齒
  • gear : n 1 【機械工程】齒輪，（齒輪）傳動裝置，齒鏈；排擋。2 〈古語〉衣服；甲胄與武器。3 傢具；財物，動...
  • teeth : n. tooth 的復數。
  1. Finite element analysis on the gear - shaft of helical gear teeth

    某斜齒輪輪軸的有限元分析
  2. Fundamental rating factors and calculation methods for involute spur and helical gear teeth

    漸開線正齒輪齒和斜齒輪螺旋齒的基本額定因子和計算方法
  3. Helix angles for cylindrical gear teeth

    圓柱齒輪嚙合的螺旋角
  4. Gears - wear and damage to gear teeth - terminology

    齒輪輪齒磨損和損傷術語
  5. Exact modeling of gear teeth is based on meshing theory

    摘要根據齒輪嚙合原理，建立了輪齒的精確齒形。
  6. Tolerances for cylindrical gear teeth ; tolerances for pitch - span deviations

    圓柱齒輪嚙合公差齒距偏移公差
  7. Cylindrical gears - iso system of accuracy - part 1 : definitions and allowable values of deviations relevant to corresponding flanks of gear teeth

    圓柱齒輪. iso精度體系.第1部分:齒輪嚙合對應齒根面的相應偏差定義和容許值
  8. Cylindrical gears. iso system of accuracy. part 1 : definitions and allowable values of deviations relevant to corresponding flanks of gear teeth

    圓柱齒輪. iso準確度體系.第1部分:與齒輪齒對應齒根面有關的偏差的容許值和定義
  9. 3, during the process of the gear teeth meshing, the film shape and pressure distribution have little difference. but, the temperatures have the distinctive changes as the engaged position is varied, which means that the temperatures as the increase in the rate of slide to roll

    3 、在齒輪傳動嚙合過程中，壓力分佈和油膜形狀無明顯變化，但溫升隨嚙合位置的不同呈顯著變化，即溫升隨著滑滾比增大而增大;在單、雙齒嚙合交替處，摩擦系數達到極值，可達0 . 08 。
  10. In the process of actual usage, two problems about a certain type bf cargo truck appear. the first one is the burnt clutch and the second is the fracture of gear teeth of the sixth gear

    在實際使用過程中，某重型載貨汽車出現了離合器摩擦片燒傷及變速器六檔齒輪輪齒折斷兩個問題。
  11. Cylindrical gears code of inspection practice part 1 : inspection of corresponding flanks of gear teeth

    圓柱齒輪檢驗實施規范第1部分:輪齒同側齒面的檢驗
  12. Tolerances for cylindrical gear teeth ; tolerances for tooth trace deviations

    圓柱齒輪嚙合公差.齒面線偏移公差
  13. In this paper, based on the theory of ehl ( elasto - hydrodynamic lubrication ), a study is conducted to investigate the impacts of geared factors ( including gear speed ratio, gear teeth modulus and center distance ) on the lubrication behavior of gearing, and some useful conclusions are obtained

    應用彈性流體動力潤滑理論，計算分析了傳動比、模數及中心距等齒輪參數對齒輪副潤滑性能的影響，得出了一些有益的結論。
  14. The calculating of bevel gear teeth shape coefficient y follows the formula below

    斜輪形系數y的計算採用下列公式：
  15. Information on gear teeth in drawings ; information on involute teeth for cylindrical gears

    圖紙上齒輪嚙合信息第1部分:圓柱齒輪漸開線嚙合信息
  16. Study of determining method of number of gear teeth in shifting system of machine tools

    機床變速系統齒輪齒數設計方法研究
  17. Applying the computer program developed by this paper, and choosing the real values of the gear transmission, this paper has completed more than 50 sets of calculations of the thermal elastohydrodynamic lubrication based on the non - newtonian fluid. the following conclusions can be drawn according to the computational results : 1, when the gear teeth are engaged at the pitch point, the changes of both the gear rotational speed and the load have little influence on the pressure distribution and the film shape, but they have large influence on the film temperature distribution

    應用本文研發的計算機程序，選用齒輪傳動的實際參數，先後進行了50餘組的基於非牛頓流體的熱彈流潤滑計算，所得的主要結論如下： 1 、當齒輪在節點嚙合時，齒輪轉速及載荷的變化對壓力分佈口太原理工大學碩士學位論文和油膜形狀的影響不大，但對溫度分佈有明顯的影響。
  18. Rating the pitting resistance and bending strength of generated straight bevel, zerol bevel and spiral bevel gear teeth

    直齒傘齒輪齒，弧齒傘齒輪齒，螺旋傘齒輪齒的耐點蝕性和彎曲強度的評定
  19. Abstract cutter teeth and gear teeth are simplified as mechanical models, the bending deformation at contact nodes is calculated by applying the three - dimension finite element method and analyzing their mechanical condition, the relation curve between shaving force and bending deformation is drawn out

    簡介：摘要將刀齒和輪齒抽象簡化為力學模型，分析其受力狀態，並運用三維有限單元法計算各節點的彎曲變形量。
  20. The result of study shows that there are rather big effects on the statistics of load spectrum of gear by considering the load distribution among gear teeth, and lowered the result of prediction on bending fatigue life of gear

    研究結果表明，考慮齒間載荷分佈對齒輪載荷譜的統計特徵有較大影響，並降低了齒輪的彎曲疲勞壽命預測結果。
分享友人
分享到 Line

分享到臉書