high silicon surface layer 中文意思是什麼
high silicon surface layer
解釋
高硅表面層-
Sige simox : oxygen ions with high dose were implanted into sige grown directly on silicon substrate for the first time, and sige - oi novel structure was formed successfully with additional high temperature annealing ; it has been confirmed that oxygen implantation with 45kev, 3 1017cm - 2 and annealing at 12500c in ar + 5 % o2 for 5 hours, are fit for the formation of sige - oi structure ; ge loss during the high temperature annealing has been observed, which is originated from ge volatility and ge diffusion ; it has been proposed to use nanoporous layer induced by h + / he + implantation to surppress ge diffusion and to use surface oxidation to overcome the upper limit of sige simox. sige smart - cut : hydrogen ions were implanted into sige material and followed by high temperature process ( 4000c to 7000c ) ; blistering study was done and suggested the possibility of sige layer transfer by smart - cut technology ; it is concluded that the bubble formation is easier in sige than in si, and the strain in sige / si and the difference of binding energy in sige and in si could possibly contribute to this effect. behavior of sige / si implanted with hydrogen : gave a detailed study on sige implanted by beamline or phi hydrogen implantation ; it has been found that great strain is introduced into sige by hydrogen implantation and this strain could be alleviated by high temperature annealing ; both for conditional beamline implantation and piii hydrogen implantation, 600 is appropriate for the post - implantation treatment
Sige - simox工藝方面：首次採用硅（ 100 ）襯底上直接外延的100nm厚sige的樣品中注入高劑量的o離子，通過退火處理成功制備了sige - oi新結構，即sige - simox工藝，證實了以45kev注入3 10 ~ （ 17 ） 7cm ~ （ - 2 ）劑量的氧離子，隨后在氧化層的保護下經1250 ， ar + 5 o _ 2氣氛的高溫退火（ 5小時）過程，可以制備出sige - oi新型材料；實驗中觀察到退火過程中的ge損失現象，分析了其原因是ge揮發（ ge通過表面氧化層以geo揮發性物質的形式進入退火氣氛）和ge擴散（ ge穿過離子注入形成的氧化埋層而進入si襯底中） ，其中ge擴散是主要原因；根據實驗結果及實驗中出現的問題，對下一步工作提出兩個改進的方案：一是通過在si襯底中注入適量h ~ + / he ~ +形成納米孔層來阻斷ge擴散通路，二是可以通過控製表面氧化來調節安止額士淤丈撈要表面sige層中的ge組分，從而部分解決sige -
As far as the new technology of selective diffusion, the method of printing is used and the phosphoric paste ( high concentration ) is printed at the electrode - site in silicon. afterwards, a thin layer of phosphoric source ( low concentration ) is sprayed on the surface of the non - electrode - site in silicon
在選擇性擴散新工藝中，我們採用絲網印刷電極的方法在矽片的電極位置印刷濃度較高的磷漿（摻磷sio _ 2乳膠） ，在非電極區噴塗一層濃度較低的磷源，擴散后形成重摻雜和輕摻雜。
分享友人