hydrostatic structure 中文意思是什麼
hydrostatic structure
解釋
水工結構- hydrostatic : adj. 流體靜力（學）的；靜水（學）的。
- structure : n. 1. 構造，結構；組織；石理，石紋。2. 建造物。3. 【化學】化學結構。4. 【心理學】（直接經驗中顯現的）結構性，整體性；整體結構。adj. -d ,-less adj.
-
The principle, the characteristics, the structure design and the supporting performance of sliding shoes hydrostatic bearing of water hydraulic pump are analyzed and investigated in this thesis
本文對水壓滑靴靜壓支承的原理、特點、結構設計和支承性能進行分析和討論。 -
The paper also analyzed that different spindle structures and bearing arrangements influenced load - bearing characteristics of motorized spindle, finally obtained excellent multi - support hydrostatic bearing motorized spindle structure
分析了不同主軸結構和軸承布置對電主軸承載特性的影響，優選出了的多支承靜壓軸承電主軸結構。 -
This text servo each that valve control hydrostatic bearing to keep and support structure carry on exhaustive design calculate comparatively on electric liquid, and analysis in detail that has designed the electric liquid servo valve
本文就電液伺服閥控制的雙腔靜壓支承結構進行了較為詳盡的設計計算，並詳細分析設計了電液伺服閥。 -
After deducing simplified general formula, a method for calculating structure and performance parameter of water hydrostatic bearing is presented, in which the throttle function of short damping hole is employed to decrease water film thickness and to improve the bearing performance
由於滑靴的靜壓支承性能較差，因此在推導出簡化通用公式后，提出了計算水靜壓支承結構和性能參數的方法，利用短阻尼孔的節流作用來減小水膜設計厚度，提高支承性能。 -
The supporting environment of the system is formed with the integrating of apache and tomcat server. after studying the hydrostatic bearings ’ structure, function and design method, several typical and applied hydrostatic bearings and guide rails are selected, so the function of the remote design service comes true by the dreamweaver platform for programme exploiture and the techniques of html and matlab. the method is feasible after debugging
在上述研究的基礎上，提出了matlabwebsever的遠程設計服務方案，集成了apache和tomcat服務器，形成了系統的支持環境;以dreamweaver為程序開發平臺，採用html和matlab等技術，在研究液體支承的結構、功能和設計方法的基礎上，選取了幾種典型、實用的液體靜壓軸承和導軌，實現了其遠程設計服務的功能，經調試，方法可行。 -
The structure is supported by a raft foundation, and where required, tie - down anchors are used to prevent hydrostatic uplift
上部結構由筏板基礎承重，並且根據要求在筏板基礎上打上了系緊螺栓以抵抗靜水浮力。 -
Considering cavitation and the coupling of solid and fluid, the structure responses caused by combination of underwater explosion and hydrostatic pressure are simulated through modeling shell structure and its outer water
通過對殼體結構及外部水域進行建模，並考慮流固耦合及空泡因素，模擬出結構受水下爆炸載荷及靜水壓力聯合作用下的響應。 -
By way of comparing the results obtained from netting theory, compound theory, nonlinear fem and experimental test, the conclusion could be drawn that matrix crack damage surely existed in the cylinder part of structure. when the structure was subject to internal pressure up to 6. 8mpa, which was the maximum loading of hydrostatic test, the deformation of the global structure and stress and strain distributed in any parts of structure were obtained
通過對網格理論、復合理論和非線性有限元方法計算結果與試驗值之間的相互比較，可以看出：非線性有限元計算結果介於網格理論和復合理論之間，且有限元計算結果與復合理論結果更加接近，表明在水檢壓力下殼體筒段確實存在著基體開裂等損傷。 -
By x - ray analysis of the obtained samples the degree of the reaction was researched when the time of ball milling changed. at last the regularity of the metallurgical structure of tial alloy was investigated, when the high temperature changed. the following aspects were accomplished after hot hydrostatic extrusion
熱靜液擠壓工藝:擠壓后，坯料緻密度有了較大的提高;分析了球磨時間跟擠壓力的關系;對ti - al基合金室溫斷裂方式及斷口形貌進行了一定的研究。 -
Spread the structure of annular rectangular hydrostatic cushion equivalently
環矩形靜壓墊結構的等效展開 -
Taking the hydrostatic equilibrium of axial force of pump dm360 as the example, this paper elaborates design calculation and dynamic - static characteristic analysis of hydrostatic bearing with twisting plate throttle, derives design parameters and formulas of bearing structure, discusses effects of various main factors ( oil viscosity, compressibility, distortion coefficient of twisting plate, pressure of oil source, and bearing clearance ) on dynamic characteristic, and obtains some conclusions about the application of hydrostatic bearing in engineering practice
本文以dm360型泵軸向力的液體靜壓支承平衡為例，對扭板節流靜壓支承的設計計算和動靜態特性分析進行了較為詳盡的闡述，推導出支承結構的設計參數和公式，討論了各種主要因素（油液的粘度、油液的可壓縮性、扭板變形系數、供油壓力、支承間隙）對支承動態特性的影響，給出了一些結論。
分享友人