indentation depth 中文意思是什麼

indentation depth 解釋
壓痕深度
  • indentation : n. 1. 呈鋸齒形；缺刻。2. 海岸線凹入處。3. （印刷或書寫中每段首行開端的）空格。4. 凹痕。
  • depth : n. 1. 深；深度。2. （色澤的）濃度；（聲音的）低沉；（感情等的）深厚，深沉，深刻。3. 進深。4. 〈常 pl. 〉深處；深淵，深海，海。5. 正中，當中。6. 深奧，奧妙。
  1. Methods of test for paints - determination of knoop hardness by measurement of the indentation depth

    塗料的試驗方法.用壓痕深度測量法測定努普硬度
  2. According to the experimental results, the adhesion effects to the load - depth curves are significant as the indentation depth is lower than 50 nm, and the effect gets larger as depth decreases

    由實驗結果發現黏滯效應在壓痕深度小於時，對壓痕作用力與壓痕深度圖有極大之影響，而且此現象隨著壓痕深度下降而急劇上升。
  3. The tested materials include ( 100 ) silicon wafer, ( 110 ) silicon wafer, poly - silicon thin film, dry oxidized silicon dioxide thin film, wet oxidized silicon dioxide thin film, lto thin film, standard lpcvd silicon nitride film, low stress lpcvd silicon nitride film, alumni nitride film, zinc oxide film etc. in the nanoindentation experiment of the single crystal silicon, two different mechanical phases are observed at different indentation depth

    用納米壓入法對（ 100 ）單晶硅及（ 110 ）單晶硅、多晶硅薄膜、干氧薄膜、濕氧薄膜、 lto薄膜、標準氮化硅薄膜、低應力氮化硅薄膜、氮化鋁薄膜、氧化鋅薄膜等重要材料的楊氏模量和納米硬度進行了系統地測量。報道了單晶硅在壓入過程中觀測到的兩個力學相的變化。
  4. Comparison between quasi - static indentation and low - velocity impact tests has been conducted in this paper at last. in accordance with energy balance principle, the dent depth vs. peak contact force under impact curve, which is derived from the dent depth vs. impact energy curve, is similar with the dent depth vs. indentation force curve with an evident transition

    最後，本文還對低速沖擊試驗與靜壓痕試驗做了比較分析，並基於能量平衡公式，從沖擊能量凹坑深度關系導出了沖擊最大接觸力凹坑深度關系曲線，它與靜壓痕試驗得出的壓痕力凹坑深度曲線的變化趨勢相類似，即出現較明顯的拐點。
  5. Analyzing the present status of nano - structure machining, we find the main barrier to the three - dimensional nano - structure machining is the lack of the systemic thesis on machining depth. the micro - machining by micro probe can be divided into two processes : indentation and scratching

    本文通過分析國內外相關微納米加工技術的研究現狀，針對基於掃描探針顯微鏡的微加工系統中採用原子力微探針刻劃加工三維加工中亟待解決的加工深度問題，藉助理論、模擬以及實驗手段進行了研究。
分享友人
分享到 Line

分享到臉書