induction by current 中文意思是什麼
induction by current
解釋
電流感應-
Induction heated oil tempered spring wire is a kind of new technical material which has been developed since 1980s. it can be heated by means of eddy induced into itself through electromagnetic coil and this method is mainly used in surface quenching. with correct designing and reasonable current frequency, induction coil and heat treatment process selected, as well as plc controlling applied, the wire can be uniform heated along cross - sectional and longitudinal direction and can be quenched and tempered continuously
應加熱油淬火-回火彈簧鋼絲，是二十世紀八十年代發展起來的新技術材料，在國外稱為itw induction heat oil tempered spring wire 。是通過線圈電磁感應鋼絲本身產生的渦流進行加熱，通常主要用於表面淬火。經正確設計，選擇電流頻率，合理的感應線圈及熱處理工藝，並實施plc控制，可使鋼絲整個截面及長度上得到均勻加熱，進行連續整體淬火和回火。 -
The stresses and nonlinear deformations of thin strip - plate with two simply supported edges under the coupled action of the electromagnetic field arid mechanical load are calculated, the magneto - elastic effects on thin current - carrying strip - plate by the side current and electromagnetic induction density are studied
由此計算分析兩邊簡支條形薄板在電磁場和機械載荷耦合作用下的應力與變形，研究側向電流和外磁場強度對載流條形薄板的磁彈性效應。 -
In this paper, several scheme of vscf is compared firstly, of which gets doubly - fed generating mode. doubly - fed vscf wind power generating system uses a doubly - fed induction generator, which rotate speed can be able to change with wind turbine, and it ensures a constant - frequency output, by controlling the frequency of current input into rotor windings. in vector trans control system, the control of stator active power and the control of stator reactive power can be essentially decoupled, and the former is via torque component and the latter is via exciting component of stator current
本文首先比較了幾種變速恆頻方案，從中選擇了雙饋式變速恆頻方案；它運用雙饋電機的工作原理，允許發電機轉速變化，而在電機轉子側接入低頻勵磁電流，通過控制該電流的頻率，保證雙饋電機定子輸出的頻率恆定；再結合矢量控制技術，通過調節轉子電流來控制定子電流的轉矩分量和勵磁分量，相應獨立地控制發電機輸出的有功功率和無功功率。 -
There are five parts are as follows : in part one, the concept of switching function is introduced first to establish the nonlinear mathematical model of the induction motor variable frequency speed adjustment system which is fed by a sine pulse width modulated ( spwm ) inverter and takes the effect of the main magnetic circuit saturation into consideration, then the low frequency oscillation of the system is simulated according to the model. next, from the view point of energy conversion of the inverter - induction system, a criterion for the low frequency oscillation is proposed to determine whether the system is in low frequency oscillation which is judged by whether the interval of the negative current component of the inverter input current is more than 1 / fc ( fc is the carrier wave frequency of the inverter ) or not
首先引入開關函數概念，建立了正弦脈寬調制（ spwm ）逆變器供電異步電動機，考慮主磁路飽和時的變頻調速系統整體數學模型，模擬系統的低頻振蕩；其次從逆變器-異步電動機系統能量轉換角度出發，提出通過檢測逆變器輸入電流中負電流的間隔時間是否大於1 / f _ c （ f _ c為逆變器載波頻率）來判定系統是否出現低頻振蕩；最後的實驗結果驗證了系統低頻振蕩建模和判據的實用性和正確性。 -
The paper establishes mathematics model of electromagnetic heating system of eddy current field and temperature field, and gives corresponding discrete format with elements as eight nodes, hexahedron equal cell, through calculating eddy - current field to gain the internal heat source that the temperature field needed, to use discrete method to solve the problem of induction - heating part ' s temperature field by axial symmetrical electromagnetic, and then to analyze the characteristic of instantaneous temperature field
本文建立了電磁加熱系統的渦流場和溫度場間接耦合的數學模型，分析了不同頻率下渦流和溫度的分佈情況，並以八節點六面體等參元為例給出了渦流場對應的離散格式，通過計算渦流場獲得溫度場所需要的內熱源強度，加熱部件的溫度場以軸對稱格式進行離散求解，並對瞬態溫度場有限單元法的求解特點進行了分析。 -
The induction heating generates heat by means of joule effect resulting from an eddy current. it is widely used in industrial operations due to its high efficiency, precise control and low pollution properties
感應加熱利用工件中渦流的焦耳效應將工件加熱，該方法具有效率高、控制精確、污染少等特點，在工業生產中得到了廣泛的應用。 -
The paper lucubrated the control theory of induction motor ' s vector transform and the method of calculating speed by induction motor ' s torque current weight, based on which, the paper designed a close - loop speed - sensorless vector control vwf system and realized the system in matlab / simulink
本文深入研究了感應電動機矢量變換的控制理論和利用電動機轉矩電流分量進行速度推算的方法。在此基礎上設計了一個閉環的無速度傳感器矢量控制變頻調速系統。 -
Motion control is a comprehensive subject. modern ac drive is a important embranchment in the field of motion control. however, it is difficult to rea1ize high - performance ac drive systems because induction motors are a kind of strongly - coupled nonlinear system with many variables and the torque is not easy to control. with vector control technology decoupling and torque control of ac motor are solved. the basic idea of vector control is that three - phase system is equiva1ent to two - phase system by coordinate transformation and it realizes the decoupling between field current and torque current of the stator in order to control the flux and current respectively, thus induction motor can be considered dc motor and high performance is achieved easily. with the progress of electric and electronic technology and the development of computer, high - integrated special modules and high - precision digital signal processor ( dsp ) are applied to ac drive so that vector control has been developed rapidly
但是高性能的交流調速系統實現很困難，這是因為交流電機是多變量、強耦合的非線性系統，不易實現高性能轉矩控制。矢量控制技術則解決了交流電機解耦與轉矩控制問題，其基本思路? ?應用坐標變換將三相等效為二相，實現定子勵磁電流分量與轉矩電流分量之間的解耦，達到對交流電機磁鏈與電流分別控制的目的，交流電機等效為直流電機實現高性能調速。隨著電力電子技術的進步，計算機技術飛躍發展，高度集成的專用模塊和高精度的數字信號處理器應用於交流傳動系統中，促進矢量控制迅猛發展，日趨成熟。 -
Aimed at some problems such as short spraying distance, electricity - leaking and reverse ionization among electrostatic nozzles existing in the country, a induction charging and pneumatic energy electrostatic nozzle was designed. the basic designing theories, structure and working process of this nozzles were theoretically specified in the paper. and then the atomization quality and charge performances of this nozzle and its affecting factors were studied by carrying out performance experiment and statistic analysis. result of the studies indicate : ( 1 ) some progress were made in solving the problems list above ; ( 2 ) from this nozzle, droplet were minute and uniform, and higher charge - mass ratio can be obtained under lower electrostatic voltage, thus the atomization quality and charge performance of this nozzle were both better ; ( 3 ) within the experiment extend, air pressure at 0. 2mpa, electrostatic voltage at 2400v were the most suitable parameters for the nozzle ; ( 4 ) the regression equations for describing droplet size, intensity of spray current and charge - mass ratio of this nozzle obtained from the experiment data had higher forecast precision ; ( 5 ) cross - effect of all factors were not significant, the atomization quality and charge performance were relative dependency affected by the factors
諸試驗因素中，充電電壓和噴孔直徑對霧滴荷質比均有極顯著的影響；氣體壓力和液體流量對霧滴荷質比的影響均不顯著；影響霧滴荷質比的主要因素依次為充電電壓和噴孔直徑; （ 8 ）在300v 、 600v 、 1200y 、 1800y 、 2400v 、 3000v六種充電電壓t ，霧滴荷質比先隨充電電壓的增加而增大， 2400v后荷質比減小，推測:對于所研製的噴頭可能存在一個最佳充電電壓; （ 9 ）由充電電壓和噴孔直徑的不同搭配所得霧滴荷質比不同這一結果，可看出，較大充電電壓需配備較大噴孔直徑以增強霧滴荷電效果; （ 10 ） td3 . 6和td3 . 4兩噴頭的霧滴荷質比曲線趨于重合，說明噴孔直徑大於滬3 -
According to the vector control theory of an induction motor, we utilize the speed estimation and speed control by the rule that the rotor flux of the voltage model must be coincident with the one of the current models
根據異步電機矢量控制理論，本系統利用電壓模型的磁通應與電流模型的磁通相一致，實現轉速推算和轉速控制。 -
Some research about sensorless control of induction motors in recent years has been introduced in chapter one. in chapter two, a field - oriented control system with current regulator and voltage source inverter ( vsi ) is presented firstly, which is proved in theory that the voltage feed - forward decoupler can be omitted, the good decoupled control properties of flux current and torque current is also validated by experiments with speed - sensor based on f240dsp real system
論文第二章從異步電機的基本數學模型入手，介紹了一種基於轉子磁場定向的帶電流內環控制的電壓型逆變器輸出閉環矢量控制結構，在理論上證明了該模型可省略電壓前饋解耦環節，採用f240dsp晶元構建的帶速度傳感器實驗系統驗證了其定子電流勵磁分量和轉矩分量有良好的解耦控制特性。 -
To proceed with induction motor speed control task, by using the passivity of motor rotor flux subsystems, a clear and simple design for the speed control systems with inner current - loops is presented
摘要利用電機轉子磁鏈子系統的無源性，給出帶電流內環速度控制系統的一種簡明設計，以達到控制感應電機速度之目的。 -
Based the basic principle of the accumulation of induced electric charges across the resistivity discontinuities and the induction current channeling inside the conductive bodies inspirited by the mt field, we set up the relation between the measured field on the earth surface and the distribution of the induced source underground by means of the defining the electric charge occurrence probability function and the electric dipole occurrence probability function and the spacial distributing of the " correlation probability ". the " image " of the field sources underground, or the distributing graphy of the induced electric charges and the induced current in the mesuring area can be drawed, from which we can get the outline of the geological anomaly on the meaning of the probability
大地電磁場概率成像方法是一種新的地球物理成像反演方法，它是根據在大電磁波場的激勵下，地下介質電阻率間斷處產生感應電荷積累和導體內部產生感應電流，從而產生感應電磁場的原理，相應地定義了感應電荷發生概率函數和感應電偶極子發生概率函數，通過「相關概率」發生的大小的空間分佈，建立了地表觀測場與地下場源空間分佈的內在聯系。地下場源分佈概率的「像」 ，即測區的感應電荷和感應電流的概率的分布圖像，就是測區內地質體在概率意義下地質異常體的分佈輪廓。 -
Based on the analysis of the control theory of the dtc of doubly fed induction machines, in this paper, two control schemes are proposed : the least mode of rotor current and the stator power factor adjustable mode. in the first control scheme, we may make the rotor voltage the same or opposite phase with the rotor current by throwing suitable rotor voltage vector
在第一種控制方案中，通過施加轉子電壓矢量，使轉子電流與轉子磁鏈垂直，轉子勵磁全靠定子電流，即可保證轉子電流和轉子電壓同相或反相，從而實現了轉子側功率因數為1 ，可減小轉子側變頻器的容量。 -
In this paper, the current three - dimensional measuring systems in home and outsides are analysed, the design project based on optic induction technology and singlechip is put forward. in the case, the problem in orientation is solved by optic induction technology, the system is composed of integrate circuits, in the end the integration is enhanced and the design of hardware is simplified. the data collection process and communication in the system are completed by programming
在方案的實現過程中，利用先進的光學感應技術有效地解決了三維量測系統的定位問題；採用多種集成晶元構成適于專業三維量測的單片機應用系統，提高了系統集成度，簡化了系統硬體設計；通過單片機程序設計實現了三維量測系統的數據採集、處理與通信。 -
In addition the h. kantz method is applied to analyze the time series of the motor current, the maximal lyapunov exponent calculation is realized, the criterion for the motor chaos is brought forward, the existence of chaotic phenomenon in the induction motor is verified by the characteristic exponents, which proves theoretically that the chaotic movement is one of the reasons that results in the low frequency oscillation of the induction motor system
應用h . kantz方法對電機電流信號的時間序列分析，實現了最大李亞普諾夫指數的具體演算法，提出了電機出現混沌運動的判定根據，通過特徵指數驗證了異步電動機現象的存在，從理論上說明混沌運動是異步電動機系統產生低頻振蕩的原因之一。第三部分深入研究了系統低頻振蕩的主要影響因素。 -
The finite element method ( fe '. i ) is adopted to analyze the effects of the numbers of coil turns, current intensity and current frequency upon the rate of joule heat generation in details. the thermo - radiation analytical countermeasures of various types are adopted to carry out the numerical analysis of the effects of the crucible with different shapes and sizes and the blind holes with different depths opened in the tops of crucibles as well as coil positions upon the thermal field distribution whereby solving the main problem of field the thermo - field design of the induction - heating sic crystal growth system. a new combination idea of the thermo - field design obtained by means of the united design of the thermo - insulator and blind holes has been presented
採用有限元分析方法對線圈匝數、電流強度、電流頻率等對焦耳熱產生速率的影響進行了詳細的分析討論；採用不同的熱輻射分析策略，對不同坩堝形狀、坩堝頂部開設不同深度的盲孔以及線圈的位置等對熱場分佈的影響進行了數值分析，解決了感應加熱碳化硅晶體生長系統熱場設計的主要問題，提出了通過絕熱層與盲孔的聯合設計獲得所需熱場設計的思路，給出了根據軸向溫度梯度的波動對線圈位置實行動態調節以控制熱場的理論依據。 -
It uses the encouragement of step wave or other impulse current field source to produce the transition process field in earth. in the moment of shutting the power it produce the volute alternating electromagnetic field. from the abnormity of measuring the attenuation character of the second induction electromagnetic field, which produced by underground medium with time change, the conductive capacity and the position of the underground non - homogeneous substance can be analyzed
瞬變電磁法（ transientelectromagneticmethod ）是一種時間域的電磁勘探方法，利用階躍波或其它脈沖電流場源激勵，在大地產生過渡過程場，斷電瞬間在大地中形成渦旋交變電磁場，測量這種由地下介質產生的二次感應電磁場隨時間變化的衰減特性，從測量得到的異常分析出地下不均勻體的導電性能和位置，從而達到解決地質問題的目的。 -
To reduce the high starting current as asynchronous motors start up directly and eliminate the negative influence that brought about by switching of contact when it starts up with reduced - voltage means, two new methods based on power electronics technology for improving the starting characteristics of three - phase induction motor are presented. one is alternative voltage regulator, the other is alternative voltage chopper. the three - phase regulating circuit - asynchronous motors system and the three phase chopper circuit - asynchronous motors system are analyzed and simulated with matlab
為解決上述問題，本文提出一種基於斬波方式的三相交流異步電動機的軟起動新方法，論文對電路的起動特性、功率因數、諧波以及控制策略進行了研究，模擬結果表明這種基於斬波方式的三相交流異步電動機的軟起動方法比基於三相交流調壓的三相交流異步電動機的軟起動方法具優越性。 -
Power supply for induction heating is an equipment to heat the workpiece by whirling current and it is applied widely in industry because of its many virtues
感應加熱電源是利用電渦流對工件加熱的一種裝置，由於具有諸多優點而在工業中得到了廣泛的應用。
分享友人