inertia simulation system 中文意思是什麼

inertia simulation system 解釋
功率吸收裝置
  • inertia : n. 1. 【物理學】慣性，惰性，慣量。2. 不活動，不活潑，遲鈍，惰性。3. 【醫學】無力。adj. -less 無慣性的，無慣量的。
  • simulation : n. 假裝；模擬；裝病，裝瘋；【生物學】擬態，擬色。
  • system : n 1 體系，系統；分類法；組織；設備，裝置。2 方式；方法；作業方法。3 制度；主義。4 次序，規律。5 ...
  1. Inertia simulation system

    慣性模擬系統
  2. Chapter 3 gives an introduction to the flow rate dividing principle based on meter - in flow rate feedback control of multi - actuators control system. special analysis about simultaneously operating multi - actuators with different inertia loads is made. finally the results of simulation proved that the new method is an effective way to improve the flow - used ratio when the pump discharge flow rate is insufficient

    第三章介紹了基於執行器進油側流量反饋的分流控制的原理，並針對大小慣性執行器同時起動時採用該分流控制方法進行了具體分析；最後通過模擬說明該分流控制方法能在大小慣性執行器同時起動並在泵輸出流量不足的情況下有效提高泵輸出流量的利用率，並能實現優先級和分流比混合控制。
  3. Through simulation the dissertation analyzes the effect of connect stiffness, load inertia, pressure - flux coefficient to the active load system and surplus force ( torque )

    通過模擬，分析了連接剛度、負載慣量、總的壓力流量系數對主動加載系統和純多餘力的影響。
  4. In addition, at this strong coupling, heavy inertia, non - linear, uncertain system, it initial proposes and adopts multi - mode segmented intelligent fuzzy control strategy. the control strategy was carried on the simulation experiment by the data making through producing the scene, having made the good control result. considering still that change of environmental temperature impacts on temperature of steel pipe, in which fbe is colloidized, it put forward the method of adjusting temperature setting value according to environmental temperature

    另外文中又對這一強耦合、大慣性、非線性、不確定系統，提出了採用智能模糊多模態分段控制策略，通過在生產現場取得的數據對該控制策略進行模擬研究，取得了良好的控制效果；還考慮到環境溫度變化對fbe膠化時鋼管溫度的影響，提出了依據環境溫度變化調整溫度給定值的方法，模擬證明了該演算法的有效性。
  5. The core control of the whole control system is accomplished by plc, including sequence action control, numerical calculation, processing control of frequency and so on, and the realization of vvvf is accomplished by transducer. the simulation of inertia load is completed well by union of both plc and transducer

    整個控制系統的核心控制由plc完成，包括動作順序控制、數值計算、頻率的過程式控制制等，而變頻調速的實現靠變頻器來完成的，兩者相互結合較好地完成了慣性負載的模擬。
  6. The air bearing is the most important part of an attitude control system simulator for simulating a satellite moving in the weightless circumstance. performance of a satellite attitude simulation system based on air bearing is decided by the inertia matrix and gravity disturbance torque arising from a difference between mass center and rotation center, and air bearing can be used to simulate the algorithm of on - line mass - property parameters identification on the ground. so the problem of mass - property and gravity disturbance torque identification for satellite and air bearing is studied in this thesis

    氣浮臺能夠模擬衛星在軌失重條件下的姿態運動，是衛星姿態控制系統物理模擬的核心部件，其轉動慣量和質心偏移引起的重力干擾力矩等決定了基於氣浮臺的衛星姿態物理模擬系統的性能，並且利用氣浮臺可以實現衛星質量特性在線辨識演算法的地面物理模擬驗證，因此本文對衛星和氣浮臺的質量特性及干擾力矩在線辨識問題進行深入研究。
分享友人
分享到 Line

分享到臉書