lift valve 中文意思是什麼

lift valve 解釋
開閥
  • lift : vt 1 舉起，使升起，提起，抬起；提高；提升。2 使高尚；鼓舞。3 運送，搬運；空運 （ ＝ airlift） 4 ...
  • valve : n 1 【機械工程】閥，活門，舌門；汽門。2 【解剖學；動物學】瓣，瓣膜；（貝）殼瓣；【植物；植物學】...
  1. Once the water reaches its maximum speed, the valve slams shut and pressure is built up in the pump. this pressure forces open a second valve linked to the delivery pipe. when nullah water falls past the hydraulic ram, its momentum will lift a tenth of the water to a storage tank located near the esther li building photo 2

    泵內有活門，當溪水在流動中受阻，會產生比正常壓力高十倍以上的瞬時水錘壓力，此時，泵內的另一活門會打開，把十分之一的溪水抽往設于李慧珍附近的儲水缸備用（圖二） 。
  2. Recommended practice for gas lift valve performance testing

    氣舉閥性能試驗方法
  3. Lift retainer and check assembly from valve body

    從閥體內取出護圈和止回閥總成。
  4. The controllable ability of valve timing, duration, and lift in the haecvvs has been proved. the map of common rail pressure, duration of control signal and the peak lift, the map of common rail pressure, duration of control signal and valve event duration, the map of the combination ability of valve event duration and valve peak lift etc. have been obtained from the experiment

    在研究了電控可變氣門系統氣門正時、氣門開啟持續期、氣門升程的可控性的基礎上，整理了共軌壓力、控制信號持續時間與氣門峰值升程的map圖，共軌壓力、控制信號與氣門開啟持續期的map圖，氣門升程與氣門開啟持續期配合范圍map圖。
  5. Lift pressure plate ( 7 ) to withdraw diaphragm and stem from valve

    提升壓力板（ 7 ） ，從閥門內退出隔膜和閥桿。
  6. Screw lift valve

    螺旋提升閥
  7. Handle assembly is removed by loosening bolt and pulling upward. remove the two hold - down bolts and lift index plate from valve

    通過鬆懈螺栓並拔出方法拆卸手柄總成。拆卸兩個緊固螺栓，提起閥門上的刻度板。
  8. Valve lift usting gear

    閥升程調整機構
  9. Lift check valve module straight out, taking care not to hit and damage seat ring

    直接將止回閥模塊取出，小心不要碰到和損壞閥座環。
  10. Lift the check valve module straight out taking care not to hit and damage the seating

    筆直地將止回閥模塊提起，要注意不要撞擊和損壞閥座密封。
  11. Eccentric gas lift valve

    偏心氣舉閥
  12. Standing clear of the outlet ( discharged water may be hot ), slowly lift and release the lever handle on the temperature and pressure relief valve to allow the valve to operate freely and return to its closed position

    經常清洗出口（排泄水可能是熱的） ，慢慢提起並釋放降溫減壓安全閥上的杠桿手柄，使得閥門能夠靈活工作並恢復到關閉位置。
  13. Never lift a cylinder by the cap, valve or guard, unless it has been specifically designed for the purpose

    不要用瓶帽、閥、護罩提升氣瓶。除非專門設計舉重用的。
  14. The hydraulically actuating, electronically controlled variable valve actuator, the common rail hydraulical source and the electronic control unit have been designed and developed. the primary control strategies of the valve timing in different conditions have been discussed. the performance of the system has been researched deeply by experiments, from which, plenty of rules have been obtained, and the way to adjust valve timing, lift and duration has been put forward

    研製了電控可變氣門系統的執行器? ?電控可變氣門驅動機構，設計了電控可變氣門系統的液壓驅動源? ?中壓共軌液壓源，開發了電控可變氣門系統的電子控制單元，實現了在不同工況下，氣門正時、氣門開啟持續期、氣門升程柔性的電子控制，並對不同工況下配氣正時的控制策略進行了初步探討。
  15. The contents of the thesis are as follows : ( 1 ) all the contents : magnetism sense fuel injector is designed. needle valve lift signal, rotation speed signal and pressure signal are collected and processed. circuit is designed. programme is programmed. ( 2 ) contents studied : the item is completed

    本課題的研究內容有: （ 1 ）本課題所要研究的內容包括:磁感噴油器的設計;針閥升程信號、主軸轉速信號、噴油壓力信號的採集與處理;系統硬體電路的設計;軟體編程等。
  16. The technical line of the thesis is as follows : formula of quantity of fuel injection is got by studying relation of quantity of fuel injection and needle valve lift, time of fuel injection, rotation speed and pressure, and quantity of fuel injection is displayed

    本課題研究的技術路線為:通過研究噴油量與針閥升程、噴油時間、主軸轉速、噴油壓力等的關系，推導出精確的噴油量計算公式，最終由顯示器顯示噴油量。
  17. The authors carry out data collection and calculation for fuel injection pressure and needle valve lift signals measured on the fuel pump test bed by using self - developed software. on the basis of experiments, four criteria for analysing fuel injection process are proposed and the comparison of performances between au and nu type fuel outlet valves is made

    作者用自行開發的軟體對在油泵試驗臺上測得的噴油壓力、針閥升程信號進行了數據採集和計算，在試驗的基礎上提出了分析噴油過程的四個判據，給出了au型和nu型出油閥的性能比較結果。
  18. The valve operating mode starts to change the moment the lift becomes zero

    當生程一變成零，汽門操作模式就開始變換。
  19. Non - return ( stop - check ) valves provide the same function as a globe valve with the addition of providing piston - lift - check valve protection in the event of backflow

    逆止閥（截止止回閥）具有與截止閥相同的功能，還有活塞提升式止回閥的功能，防止出現意外的迴流。
  20. Valve lift diagram

    閥升距圖
分享友人
分享到 Line

分享到臉書