load analysis 中文意思是什麼

load analysis 解釋
負載分析
  • load : n 1 裝載，擔子；負擔；工作（負荷）量。2 （車船等的）裝載量；一馱，一車，一飛機。3 【電、機】（機...
  • analysis : n. （pl. -ses ）1. 分解，分析；【數學】解析。2. 梗概，要略。3. 〈美國〉用精神分析法治療（＝ psychoanalysis）。
  1. The dead load analysis need not be revised.

    不需要重新進行靜載分析了。
  2. Standard test method for maximum media density for dead load analysis of green roof systems

    新暴露頂層系統靜荷載分析用最大介質密度的標準試驗方法
  3. Load analysis of undercarriage landing on the pavement

    某新機在鋪砌道面上起降時起落架受載分析
  4. The first step is form finding ; the second is load analysis ; the last step is cutting pattern design. the first and the last step are the most important

    第一階段是找形設計階段；第二階段是荷載分析階段；第三個階段是裁剪分析階段。
  5. With the material dynamic constitutive equation including damage and the effect of stain rate the predictable formula about ballistic limit velocity of fiber composite target. secondly based on the damage feature about ceramic / fiber composite target caused by impact load, analysis model about defense performance of ceramic / composite material target is formed and the predictable formula about ballistic limit velocity is also given. lastly using the reflection and projectile theory of stress wave the paper discusses the design of ceramic / composite material target, optimizes the design of double layer ceramic / composite targets, gains optimal coefficient under certain area density and discusses the variety relationship of area density and thickness with optimal coefficient u nder some ballistic limit velocity 3

    首先，分析了纖維類正交鋪層復合靶板在沖擊載荷作用下的損傷破壞機理，結合包含損傷和應變率效應的材料動態本構方程，建立了纖維復合材料板彈道極限速度的預測公式；其次，根據陶瓷/纖維材料復合靶板在沖擊載荷下的破壞特點，建立了陶瓷/復合材料靶板抗彈性能分析模型，給出了彈道極限速度預測公式；最後，利用應力波反射和透射理論討論了陶瓷/復合材料靶板的設計問題，對雙層陶瓷復合靶板的優化設計進行了分析，給出了在一定面密度下的最佳優化系數，討論了一定彈道極限速度下的面密度和厚度隨優化系數的變化關系。
  6. Firstly, for the system of moulding board and support frame in construction the side pressure and screws are analyzed. the material and structure form of support frame are discussed. the design of support frame uses the method of limited state, and also it analyses the integer stability, part stability, and single stability, and then proposes the load analysis of multi - level support frame

    首先，針對轉換層梁模體系及支撐架施工，重點分析了轉換層結構現澆混凝土對模板側壓力值及模板對拉螺桿的計算；討論了轉換層支撐體系的形式及構造，詳細論述了基於極限狀態設計的支撐架計算方法，包括縱橫向水平桿的強度驗算、立桿的整體穩定性、局部穩定性、單肢桿件穩定性等驗算，並提出了多層支撐架的施工荷載計算方法。
  7. In the condition of non - axisymmetrical stage separation in hypersonic flight, the problems of dynamics and kinematics of the validating vechicle and the launch vechicle are primarily analysised. it includes the movement of the center of mass and the rigid body of the vechicles, the relative movement of the different vechicles, the relative movement of the special parts of the different vechicles, the load analysis and the probable collision in the process of stage separation

    研究了在高超聲速狀態下非對稱級間分離過程中，驗證飛行器與運載火箭分離時的相關運動學和動力學問題。包括:飛行體質心運動和剛體運動;不同飛行體之間的相對運動;不同飛行體上特殊部位之間的相對運動;分離過程中各相關飛行體上的載荷分析和分離過程中可能發生的碰撞問題。
  8. The characteristics of traditional electric flow load analysis method are also summarized

    利用靈敏度分析方法研究了電力系統的安全性，並提出了系統過負荷時的控制方法。
  9. This thesis introduces systematically current developing situation of hydraulic engineering and static - dynamic load analysis theory and fea theory

    本文系統地介紹了進水塔結構分析的發展現狀、結構靜動力分析理論、有限元方法及理論。
  10. The nonlinear analysis of reinforced concrete slabs includes the ultimate load analysis and the finite element analysis

    鋼筋混凝土板的非線性分析方法主要有極限分折和有限元分析。
  11. The second part is load analysis. bases on the form - finding, the stress, strain and displacement etc are calculated under loads. also the problem of membrane drape and cable relaxation should be considered during this procedure

    第二階段是荷載分析階段，即找形分析獲得的曲面在各種可能荷載組合的作用下，求解其變形、位移、索膜內力及判別薄膜是否有褶皺產生或索是否有鬆弛現象。
  12. Design of industrial ethernet network system with load analysis and ga

    基於負載分析與遺傳演算法的工業以太網控制系統設計
  13. Single load analysis of measured high voltage of three - phase three - line power meter

    三相三線有功電能表計量高壓單相負載分析
  14. Subject in the way algorithmic theory, network load analysis, or even requirement acquisition, are

    部署不是一個像演算法理論、網路負載分析或者甚至是需求獲得那樣
  15. But even if you make these changes and eliminate all the places where cmps are called outside of the scope of a global transaction, a load analysis tool one that measures the performance of the system under near production conditions, like

    但是即使您做了這些更改，並且消除了所有在全局事務外部調用cmp的地方，負載分析工具（在生產環境下測量系統的性能） ，比如
  16. First, build the building model and air conditioning dynamic cooling load analysis model of the stock exchange in the basis of the experiment. second, calculate the air conditioning dynamic cooling load in summer ( april to october ) hourly by software simulation, obtain the maximum cooling load daily, the minimum cooling load daily, the proportion of each cooling load occupying the total cooling load and cooling load time frequence, analyse them by using twin load curves. last, contrast theoretical calculations with test results, analyse them and prove the model proper

    首先，以實驗為基礎建立了證券營業部的建築模型及空調動態冷負荷分析模型；其次，通過逐時逐日計算出了其夏季（ 4月? 10月）空調動態冷負荷、各分項冷負荷在空調總冷負荷中所佔的比例及空調冷負荷時間頻數，並運用雙負荷曲線法對每日最大冷負荷與每日最小冷負荷進行分析；最後，與實測數據進行對比，二者曲線基本符合，效果良好，證明所建模型適當。
  17. Cooling load analysis and energy efficiency methods of the whole glass curtain wall

    大玻璃幕墻建築冷負荷分析與節能措施
  18. Limit load analysis of simply supported annular plate under linear load

    應力約束下三維連續體結構拓撲優化分析
  19. Application of parametric fem program in thermal load analysis of piston

    參數化有限元程序在活塞熱負荷分析中的應用
  20. Ultimate load analysis of plate girders by spline finite strip and plastic hinge method

    樣條有限條塑性鉸法分析板梁的極限荷載
分享友人
分享到 Line

分享到臉書