load change test 中文意思是什麼
load change test
解釋
變負荷試驗-
Modeling the general solid web continuous box girder and opening - in - web ( open web ) continuous box girder by ansys finite element modeling tool, node stress of governing section and corresponding shear lag values are analyzed. the solution is validated by comparing with variational results and modeling test values. based on the model, the section shear lag induced by dead load, prestress tendons and car loads under the most unfavorable condition and lateral symmetry are also approached. the influence of shear lag effect in double - level continuous box girder is considered with opening - in - web and the web location. the analysis indicates that double - level - load arouses less shear lag effect than one - level - load. when self - weight and prestressed tendons act on together, the shear lag effect on box girder take on a evidently change
基於所建立的有限元模型，本文分別對實腹和腹板開孔兩種箱梁在恆載、車載、預應力荷載作用時，各主要截面的剪力滯效應進行分析，通過施加縱向最不利的和橫向對稱的車輛荷載，研究實腹連續箱梁和空腹連續箱梁在承受雙層荷載和單層荷載時引起的剪力滯效應，並考慮腹板開孔及開孔位置對于連續箱梁剪力滯效應的影響。分析表明，雙層車載對于箱梁引起的剪力滯系數比單層車載的影響要小，對于箱梁中存在引起的剪力滯后現象有一定的改善作用。 -
Based on test result of load - deformation hysteresis curve under cyclic load, fatigue damage variable is defined from energy angle, the change rule of fatigue damage is pointed out
通過對循環加載下裂隙試樣滯回特性和滯回能試驗結果的分析，從能量的角度定義了損傷變量，並指出了疲勞損傷的發展規律。 -
You can change the load pattern for a scenario by using the load test editor
通過使用「負載測試編輯器」可以更改方案的負載模式。 -
Second, engine ' s partial velocity characteristics model and universal characteristics model are built the throttle opening is considered as an essential factor to build the model for reflecting the actual working performance of engine. the situation of the throttle opening change is studied, and a simulation method is given to use torque curved surface and vehicle dynamics equation on base of differential approach method. engine test software is developed for the engine no - load test, variable throttle opening test and throttle step change test
其次，建立了發動機的部分速度特性模型和萬有特性模型；為了更好的反映發動機的實際工作特性，將油門開度作為一個重要參數參與建模，並對發動機變油門的情況進行了研究；結合轉矩曲面和整車動力學方程，採用微區間逼近法確定了發動機變油門過程模擬方法；開發了發動機試驗測控軟體，利用該軟體進行了發動機空載響應試驗、發動機不同油門開度試驗和油門階躍變化試驗，並對實際試驗數據和數學模型計算數據進行對比；在vc + +平臺上開發了發動機特性模擬模塊，在系統中用軟體實現了變油門控制發動機特性的功能。 -
Through the test of the separating sieve ' s and beams vibration acceleration, the dynamic bending moment, torque and shearing force as well as the analyze of each parameter by dividing rotation speed range from 300 r / min to 600 r / min of the main shaft, the change regularity of the vibration of the separating sieve, the vibration and the dynamic load on dangerous cross section with the change of rotation speed of the main shaft is obtained. research shows that there exits apparent relevance between the vibration as well as the dynamic load of the main beam and the vibration of the separating sieve. the vibration of the separating sieve mainly affects the composition of low frequency of the vibratio n of the main beam, appropriately amending the vibration acceleration of the separating sieve, the loading and vibration of the mam beam can be directly improved
通過分檔測試主軸轉速在300 600r min范圍內分離篩與梁的振動加速度、梁所承受的動態彎矩、扭矩和剪力以及各參量的時頻域分析，得到了主軸轉速與分離篩振動、主梁的振動及其危險截面的動態載荷間的變化規律，研究表明梁的振動和其所承受的動載與分離篩的振動之間具有明顯的相關性，分離篩的振動主要影響梁振動的低頻成分，適度改善分離篩的振動加速度，可直接改善梁的負載和振動特性。 -
Sudden load change test
突變負荷試驗
分享友人