low-carbon heat 中文意思是什麼
low-carbon heat
解釋
低碳鉛熔煉-
According to these, the paper put forward some countermeasures : select low carbon steel or low metal alloy steel with lower intensity, like 20r steel ; while welding, adopt strict craft measures with lower welding heat to input ; after jointing, proceed the whole hot dissolving on time ; control each welding joint with hardness hb 185 ; add 0. 25 % water into the liquid ammonia as decay eclipse ; enhance checking in operation, repairing equipment in time through regular interior and exterior checking
針對上述原因提出了防止氨冷器類臨氨壓力容器產生應力腐蝕裂紋的對策：選用強度稍低，但抗裂性較好的低碳鋼和低合金鋼，如用20r鋼製造；焊接時應採用嚴格的工藝措施和較低的焊接熱輸入量；焊后應及時進行整體消除應力熱處理；控制焊接接頭各區硬度hb 185 ；在液氨中添加0 . 25 %的水作為緩蝕劑；在運行中加強檢查，及時進行停車檢修時的內外部檢查和定期檢驗。 -
Purposes : this product applies to fireproof layer and oxygen - resisting layer for low smoke, non - halogen, innocuity, high grade cleaned non - flammable cables and fireproof cables, it can absorbs vast amounts of heat during burning process and forms into a carbon layer to isolate air and prevent the cable from buring further
用途：該產品用作于無鹵低煙、即無公害，高檔潔凈的阻燃電纜和耐火電纜的隔火、隔氧層，在燃燒過程中能吸收大量熱量，並形成碳殼層、隔絕空氣，阻礙電纜進一步燃燒。 -
Low grade fuels and / or polluted air can cause gum, varnish and carbon deposits to be formed in the carburetor during comustion which can result in rough idling, stalling and incrased gasoline consumption. 3 + 3 cleaner ' s superior formula will effectively remove gum, varnish and carbon deposits when sprayed directly into the carburetor, 3 + 3cleaner will clean carburetors, linkage, automatic chokes, pcv valves, heat risers, the spark plugs and the entiro system while lubricating and femoving moistuer on all moving parts, use 3 + 3 cleaner to restore efficiency, increase engine power maintain high gasmileage and have a smooth running engine
空氣和汽油中的不純物質，在汽車使用過程中會產生污垢和炭積物，阻塞汽車的化油器（呼吸系統） ，使汽車無力及加油不暢順， 3 + 3牌化油器強力清洗劑獨有的特殊配方，直接噴入于化油器內，能迅速有效地清除洗化油器，火花塞及燃油系統的油漬污穢和炭積物，並對轉軸等旋轉部位提供潤滑及防銹保護，減少積炭的產生，使引擎起動順利及平穩運轉，增強馬力及節省燃油 -
Standard specification for seamless cold - drawn low - carbon steel heat - exchanger and condenser tubes
熱交換器和冷凝器用無縫冷拉低碳鋼管標準規范 -
The specimen is obtained by collecting low carbon steel pipe experienced different time in power plant and heat treatment experiment of unused same type steel. the microstructure is analyzed by metallographies, sem, epma and tem. at the same time merchant performance is also tested
在本文所述工作中，採用金相顯微鏡、掃描電鏡、電子探針、透射電鏡等分析儀器，對上述樣品的微觀組織結構進行了分析，同時對樣品的機械性能進行了測試。 -
The carbon fibers with low strength are broken easily according to thermal tension and bend stress damage models, and the carbon fibers with high modulus are broken easily according to thermal shear stress damage model in spite of less damage caused by heat. the carbon fibers with surface glue of epoxy resin are damaged easily in physical and chemical ways because of high oxygen extent and rigidity of epoxy resin
低強度碳纖維容易在熱應力拉伸或彎折破壞模式下損傷；高模量碳纖維高溫損傷小，但國防科學技術大學研究生院學位論文容易以熱應力剪切破壞模式下斷裂;環氧樹脂表面膠剛性較大，氧含量較高，使碳纖維容易受到化學損傷和熱應力彎折損傷，均不宜用來制備c燈sic復合材料。
分享友人