measuring pressure basis 中文意思是什麼
measuring pressure basis
解釋
測壓基準-
On the basis of investigation on oscillometric technique for non - invasive blood pressure measurements, and combined the technique with pulse - wave theory, this paper designs a blood pressure and artery stiffness measuring apparatus, which not only can measure blood pressure and heart - beat - rate accurately, but can calculate the measurer ' s arterial stiffness index and vascular compliance. the apparatus provides an effective instrument for doctors to determine the measurer ' s cirrhosis level
本論文在研究分析無創血壓測量方法示波法的基礎上，結合脈搏波理論，設計出一種準確高效的血壓與血管硬度測量儀，該儀器不僅能夠準確測量出受試者的血壓與心率，還能夠計算出受試者的動脈彈性指數和臂動脈順應性，為醫生判斷患者的動脈硬化程度提供一種有效的檢測手段。 -
The traditional level measuring methods can n ' t meet our demand because the subjective investigated is in such a poor systemic condition that the temperature is a little high and there ' s so many mill dust and steam there. in this article we perform systemic discuss and research against the dynamic level measuring method under special working condition on the basis of analyzing kinds of level measuring technique in and abroad. first we establish the pressure distribution mathematic model in storage bin and then deduce the mathematic relation between level height and the uniform stress on the bottom of the bin and designed a resistance compressive stress sensor used for the special condition and put forward a resoivement according to its zero excursion existing in practical use
由於本研究系統被測對象環境溫度較高且潮濕，同時料倉中有大量粉塵及蒸汽，因此傳統的料位檢測方法不能滿足本測試要求。本文在分析國內外各種物位檢測技術的基礎上，針對特殊工況下動態物料高度的檢測進行了系統的探討與研究。首先建立了料倉中的壓力分佈數學模型，推導出料位高度與倉底均布壓力間的數學關系式，並據此設計了中溫電阻應變式壓力傳感器，同時對它在實際應用中存在的零點漂移等問題提出了改進措施，提高了傳感器性能，解決了上述特殊工況下動態物料檢測的技術難題。 -
Thus, the inner parts are found which are the main factors of the total accuracy loss. this result can offer the basis to improve the design of dynamic measurement system and to increase its measuring accuracy. in order to prove the theory of the error tracing and accuracy - loss diagnosis of the dynamic measurement, two simple measuring system are selected, that is, pressure transducer system and the dynamic measuring system based on differential mutual inductive displacement transducer
根據建立的動態系統誤差模型，以誤差溯源結果為依據，用bp神經網路分析方法，求得系統各組成單元的精度損失規律，建立其精度損失時變模型，從而找出對測量系統的總精度損失影響較大的內部組成單元，為改進動態測量系統的設計、提高其測量精度提供依據。 -
Thirdly, cbt ' s characteristic of the strain v. s. the applied pressure is studied, on the basis of this, a new scheme of the straight bourdon tube ( sbt ) is presented, a sbt is designed and fabricated, and then the strain - pressure characteristics of both the cbt and sbt are measured experimentally using a strain measuring technique, a comparison between the cbt ' s and sbt ' s strain characteristics is also made. finally, theoretical models of a fbg fluid pressure sensing system scheme based on the bourdon tube are developed, and a fbg - based fluid pressure sensing system using the transverse strain - pressure characteristic of the sbt is designed and set up
首先，詳細介紹了fbg的基本光學傳感特性，並測量了fbg的溫度、應變特性；其次，研究了c型彈簧管的位移?壓力特性，並利用ccd成像和計算機圖像處理技術對其進行了非接觸測量；再次，研究了c型彈簧管的應變?壓力特性，在此基礎上提出直彈簧管的設計方案，並製作了直彈簧管，採用應變測量技術對c型彈簧管和直彈簧管的應變?壓力特性分別進行了測量，對兩者的應變特性做了比較；最後，建立了基於彈簧管的fbg壓力傳感系統理論模型，設計完成了基於直彈簧管橫向應變?壓力特性的fbg流體壓力傳感系統。 -
On basis of practice teaching, this paper introduced some obvious features and attentions and some technic problems when measuring pressure vessels stress with resistance strain gauge
該論文介紹了當電阻應變法用於壓力容器應力測量時具有的一些明顯的特點及注意事項和可能遇到的一些技術問題。
分享友人