mechanical firing 中文意思是什麼

mechanical firing 解釋
機械點火
  • mechanical : adj 1 機械的；機械制的。2 機械學的，力學的；物理上的（opp chemical）。3 機工的，技工的；自動的；...
  • firing : n. 1. 點火；（茶的）烘烤；（陶器等的）燒成。2. 射擊。3. 燃料。4. 添煤，司爐。5. 〈口語〉解僱。6. 【無線電】觸發。
  1. In the dissertation ' s chapter 3 to chapter 5, the mechanical and physical performances of the engineering plastics are analyzed, the failure mode and the designing computing methods of engineering plastics member suffering the static load, dynamic load, impact load, pulse load, are studied. by the practice application and ball firing experiment of the engineering plastics key piece in the weapons, the precious experiences, for engineering plastics application and confirmation of the material performances guideline in the weapons, are obtained

    論文的第三章至第五章，分析了工程塑料物理機械性能，研究了受靜載荷、動載荷、沖擊載荷及脈沖載荷下工程塑料構件的失效模式和設計計算方法，通過工程塑料在槍械關鍵受力結構件上的實際應用和實彈射擊試驗，取得了寶貴的經驗，為高性能工程塑料在槍械上的應用和材料性能指標的確定奠定了基礎。
  2. The results of static firing test shows that the thermal erosion properties, mechanical properties, tand thermal shock resistance of the c / sic composites can meet a demand for thermal - structure application in the area of aerospace such as liquid rocket thruster

    試驗發動機地面熱試車結果表明，該c / sic復合材料的力學性能、燒蝕性能和熱震性能優良，可滿足宇航工程中諸如液體火箭發動機推力室等對熱結構材料的使用性能要求。
  3. It was found that there was a close relationship between the adhesion strength of the bg coating and the surface roughness of the titanium alloy and the firing temperature. the chemical state of the elements ti and si at the coating interface varied. the chemical bond and the mechanical occluding make the bg coating form a strong adhesion with the titanium alloy

    通過研究發現， bg塗層與基體的結合強度與基體表面的粗糙度以及燒成溫度密切相關，塗層界面處ti元素和si元素的化學狀態發生了變化， bg與基體強結合的機制為化學鍵和機械嵌合兩種力共同作用。
  4. Consulting about foreign study, the research showed that the speed of firing can be improved by modifying the machanism of the automatic, and at the same time two problems must be solved, one is that more mechanisms should act at the same time to reduce the time of the whole actions of automatic mechanisms, the other is that the time of each mechanism ' s action should be reduced. the time can be reduced by several ways. the first one is to reduce the mass of mechanism, the second one is to increase the force applied on the mechanism and reduce the resistance, the third one is to shorten the working distance, the fourth one is to give abstention and cushion to mechanism before action ends. this thesis includes the following topics : discussion of the theory of the automatic and shell - swing design, establish the kinematic and dynamic models of the main structures in automatic and perform the corresponding mechanical analysis, set up a compendious cyclical diagram for the automatic ; the computer simulation to the navy gun ' s firing parts

    由現有艦炮自動機循環圖可知，制約射速提高的幾個因素是：後座、復進佔用的時間較長，約占總循環時間的三分之一；供彈機的動作單獨佔用循環時間，且較長；輸彈機的輸彈時間較長；各機構動作重疊少；參考國內外的研究情況，本文提出了在採用改進完善現有自動機機構來提高射速時，必須考慮以下兩點： （ 1 ） 、力求在同一時間內能使更多的機構參與工作，並處理好各動作之間的銜接（即介面技術） ，以便縮短整個自動機的動作循環時間。
  5. Automatic release mechanical firing head

    自動丟手機械發火頭
分享友人
分享到 Line

分享到臉書