melting intensity 中文意思是什麼
melting intensity
解釋
熔化強度-
In the paper, the diabase fiber was also selected to reinforce pvc for the first time, which has high intensity, high rigidity and low cost, the diabase fiber was treated firstly, then during mixing, melting, pressing procedure, the diabase / pvc composite were prepared
本文首次對高強度、高剛度、低成本的輝綠巖纖維增強pvc復合材料進行了研究。論文首先對輝綠巖纖維進行了表面改性，然後將改性后的輝綠巖纖維與pvc混煉、壓片制備了輝綠巖纖維pvc復合材料。 -
If a current with proper intensity has been switched on, the goal of controlling the melting and welding dimension effectively around the crack tip can be obtained
文中給出的算例表明，適當控制通入的電流強度，可以達到有效控制裂尖熔化區尺寸以及形成焊口的目的。 -
The lasers used in surgeries, such as ocular surgery, dental surgery, dermatic surgery and medical surgery, are because their functional thermal ablation and melting ablation. meanwhile, the biomodulation of low intensity laser irradiation was found in many years ago. however there is still little of study focusing on the intersection of the two fields
隨著激光研究理論和生產技術的不斷發展，不但高強度激光手術在外科、眼科、牙科和皮膚科等領域獲得了越來越為廣泛的應用，而且低強度激光的光生物調節作用研究也已經獲得相當的進展，但很少有人注意到兩個領域的交叉。 -
The coupled turbulent flow field and temperature field are simulated by finite element method ; the influence of casting speed on the turbulent flow field and temperature field in the melting bath and the interaction between those two field are analyzed ; the variation tendency of the heat flux intensity between the melting bath and casting roll and law of variation with changes of casting speed in the process of solidification are given ; a comparison between the simulation results and experimental results demonstrates their good agreement ; and the mechanism of the heat flux variation is identified by analysis on the temporature gradient and development of solidification within the melting bath and its influence on the variation of the heat flux intensity
採用有限元法模擬了雙輥鑄軋不銹鋼過程的流熱耦合問題;分析了鑄軋速度對熔池內流場、溫度場的影響以及流場與溫度場之間的相互影響;給出了凝固過程中熔池與鑄軋輥之間的熱流密度變化趨勢及隨鑄軋速度的變化規律，並把此模擬的結果與試驗的結果相比較，吻合較好;通過熔池內溫度場及溫度梯度分析了熔池內凝固的發展及其對熱流密度變化的影響。 -
The applying conditions of low ti aluminum metal alloy to the car wheel rim is introduced, the result shows that, the intensity and the plasticity possessed with by in - situ titanlum alloy is better than that which adds the metal alloy of ti when melting ; the comprehensive mechanics performance of the car wheel rim made out of aluminum metal alloy is pretty much the same with that from abroad
摘要介紹了低鈦鋁合金在車輪輪轂上的應用和研究情況，結果表明，經原位鈦合金化的鋁合金的強度、塑性均明顯優于熔配加鈦的鋁合金，用該合金生產的鋁合金車輪輪轂的綜合力學性能與國外車輪輪轂相近。
分享友人