microprocessor control unit 中文意思是什麼

microprocessor control unit 解釋
微處理機控制單元（電腦）
  • microprocessor : n. 【計算機】微處理器。
  • control : n 1 支配，管理，管制，統制，控制；監督。2 抑制（力）；壓制，節制，拘束；【農業】防治。3 檢查；核...
  • unit : n 1 個體，一個，一人。2 （計值、組織、機構）單位；單元；小組，分部；【軍事】部隊；分隊。3 【機械...
  1. By using a counter and an operation microprocessor, this paper analyses the measuring method and designs an instrument of edm sinking process in discharge state. this instrument takes samples of voltage, current signal and strong and weak of high frequency signals of detecting voltage amplitude, translates them into various time pulses in discharging state. and a counting unit turns these pulses into digital signals, then send them to a microprocessor. finally various discharge time percentages are sent to the control tache

    通過采樣電火花加工放電間隙的電壓、電流信號和檢測電壓幅值上的高頻信號的強弱，得出反映間隙放電狀態的各種時間脈沖，利用計數器分別對其計數，再送給單片機運算處理，輸出控制環節所需的各種放電狀態時間百分數。
  2. Abstract : by using a counter and an operation microprocessor, this paper analyses the measuring method and designs an instrument of edm sinking process in discharge state. this instrument takes samples of voltage, current signal and strong and weak of high frequency signals of detecting voltage amplitude, translates them into various time pulses in discharging state. and a counting unit turns these pulses into digital signals, then send them to a microprocessor. finally various discharge time percentages are sent to the control tache

    文摘:通過采樣電火花加工放電間隙的電壓、電流信號和檢測電壓幅值上的高頻信號的強弱，得出反映間隙放電狀態的各種時間脈沖，利用計數器分別對其計數，再送給單片機運算處理，輸出控制環節所需的各種放電狀態時間百分數。
  3. This paper mainly researches how to transplant the embedded real - time operating system ( c / os - ) to 32 bit microprocessor unit, in order to control the temperature of an electrical resistance furnace

    本文主要研究了嵌入式實時操作系統c / os -在32位微處理器上的移植，以便於實時控制電阻爐的溫度。
  4. The ic modulation circuits and microprocessor are used in the control unit. on the side of input of inverter, the maximum power point tracking of solar module is well realized by using a kind of thought of self - optimizing control ; on the side of output of the inverter, a kind of approximate optimum v / f control strategy is used in order to optimize the match between the output of the inverter and load of motor - pump

    在逆變器輸入側，採用自尋優控制思想實現太陽能電池最大功率點跟蹤（ mppt ） ；在輸出側，採用了v / f近似優化的控制策略，以優化逆變器輸出與機泵負載之間的匹配。
  5. After analyzing the performance of lpg, this paper provided an electronic controlling lpg fuel supply system to fulfill the function of dual fuel on the diesel engine. the system use the philip 87c552 single - chip microprocessor as the cpu of the electronic control unit, with high speed valve as injector. the hardware development was discussed in detail in the paper

    本文在對lpg性能進行介紹分析的基礎上，開發了一套電控lpg燃料供給系統，實現了原柴油機的雙燃料運行；系統中的lpg供給採用高速電磁閥，系統控制硬體以飛利浦p87c552單片機為核心，配合合理的輸入輸出介面電路。
  6. The thesis presents the analysis about the process of the communication between the computer and the single chip microprocessor inside the main control unit, and gives out the related circuit realization

    文中對主控制單元中系統機與單片機的通信進行了分析，並給出了相關的電路實現。
  7. This paper sums the situations and trends of domestic and international engineering machinery firstly, discusses the demands and implements of intelligent and long - range monitoring and controlling, and constructs a three - layer model of the engineering machinery long - range monitorin and control system : the front unit control systems, the machine - mounted monitoring system and the long - range control center ; proposes a kind of structure of embedded system based on c / os - ; dissects the characteristics, structure, operation and schedule principle of c / os -, modified the kernel, and improves dependability of the schedule algorithm ; designs the hardware in detail : the microprocessor at91rm9200, the store unit, the serial interface, the human - computer interaction interface, the can bus control module, the debug interface and the reset circuit etc. ; on this basis, succeeds in transplanting c / os - to the system, sets up the operating system framework, designs the driver, sets up the institutional framework of upper user ' s application, provides the method and concrete application process of the graphical user interface module based on c / os -. the system designed in this paper, not only has the functions of local control, friendly human - computer interface, but also has various interfaces which make the system can be managed by the long - rang center

    本文首先綜述了國內外工程機械行業發展的現狀和趨勢，闡明了實施工程機械智能化及遠程監控的意義和需求，並為此構建了工程機械遠程監控系統三層結構模型:前端單元控制系統、車載監控系統和遠程監控中心;提出了一種基於c / os -的嵌入式車載監控系統構建方案;深刻剖析了c / os -的特點、內核結構、運作機理、調度演算法，在此基礎上對其內核進行移植前的必要修改，並對其調度演算法進行了可靠性改進;對構成嵌入式系統硬體的各個主要部分:嵌入式微處理器at91rm9200 、存儲單元、串列介面、人機交互介面、 can總線控制模塊、調試介面以及復位電路等做了詳細的設計;在此基礎上，成功地將c / os -實時內核移植到本文研發的嵌入式硬體系統中，建立了車載監控系統的操作系統體系結構，編寫了該操作系統的底層硬體驅動程序，建立了上層用戶應用程序的組織結構，並給出了圖形用戶界面模塊化應用程序在c / os -操作系統上的建立方法和具體應用過程。
  8. The essential features of digicone control system are the use of a microprocessor to control the winding unit. we related the hardware structure and the software design in core of mcs - 51 microprocessor and give the designing way of digicone technology

    文章中著重敘述了以mcs - 51單片機為核心的數控卷繞裝置控制系統，對該控制系統的硬體結構和軟體設計作了比較詳盡的敘述。
  9. Mcu microprocessor control unit

    微處理機控制單元電腦
分享友人
分享到 Line

分享到臉書