nominal strength 中文意思是什麼

nominal strength 解釋
公稱強度
  • nominal : adj 1 名字的，列名的。2 名義上的，空有其名的；有名無實的。3 微不足道的，輕微的。4 名稱上的；票面...
  • strength : n. 1. 力，力量，體力。2. 強度，濃度；長處；（要塞等的）抵抗力。3. 實力；兵力；全體人數，額定人數，編制。4. 筆力；文勢。5. （證券等的）市價堅挺。6. 〈美俚〉（可能有的）利潤。
  1. Aerospace ; studs with mj thread, ring locked, steel ; nominal tensile strength 900 mpa, for temperatures up to 235 c

    航空航天.公稱抗張強度900mpa .使用溫度235以下的鋼
  2. Aerospace ; studs with mj thread, ring locked, titanium alloy ; nominal tensile strength 1100 mpa, for temperatures up to 315 c

    航空航天.公稱抗拉強度1100pa使用溫度在315以下的
  3. Aerospace ; studs with mj thread, ring locked, corrosion resisting steel, nominal tensile strength 1250 mpa, for temperatures up to 425 c

    航空航天.公稱抗拉強度1250mpa .溫度425以下耐蝕鋼
  4. The test shows that nominal transverse splitting strength of concrete cylinder is well correlated to the concrete cube strength and splitting strength of cube and cylinder, especially, above interrelation is more ideal when hold - down central angle is 90

    經試驗證明，混凝土圓柱體的橫劈名義強度與混凝土的抗壓強度、立方體及圓柱體縱劈強度有很好的相關性，尤其當壓具圓心角為90時，上述關系更為理想。
  5. Aerospace ; pan head bolts with ribbed torq - set recess and mj - thread, short thread, titanium alloy, nominal tensile strength 1100 mpa, for temperatures up to 315 c

    航空和航天.帶mj螺紋短螺紋鈦合金制標稱抗拉強
  6. Aerospace ; pan head bolts with ripped torq - set recess and mj - thread, short thread, corrosion - resisting steel, nominal tensile strength 700 mpa, for temperatures up to 425 c

    航空和航天.帶mj螺紋短螺紋耐蝕鋼制標稱抗拉強
  7. Based on analysis and comparison of existing test data applied to existing ultimate strength prediction models, interfacial stress at the end of plate is deduced. after formulas for calculating the effective moment of inertia for frp - strengthened beams being revised and adjustment coefficient related to nominal main steel reinforcement ratio and curtailment length ratio being put forward, strength prediction formulas of compound beams under plate end debonding failure are established. in analysis of strength of compound beams under intermediate crack induced interfacial debonding failure mode, several bond strengths and their relation are introduced

    對于板端剝離破壞，在總結現有承載力模型的基礎上，利用已有試驗數據對各承載力計算公式進行了分析比較，進一步採用分階段分析法，推導了板端界面應力的計算公式，在此基礎上，採用加固復合梁有效慣性矩的修正公式，建立了考慮名義配筋率和板端偏移比影響的板端剝離破壞梁承載力的計算公式；對于跨中受彎裂縫導致的粘結破壞，闡述了常見的幾種粘結強度之間的區別和聯系，並基於拉剪粘結強度，提出了跨中受彎裂縫導致粘結破壞的承載力計算公式，並利用現有試驗結果確定了模型中的一些參數；最後，利用試驗數據對本文建立的兩種粘結破壞承載力計算公式進行了檢驗，結果基本吻合。
  8. Based on the above work, the calculation formulae of nominal slamming pressure and the bearing capability of the bottom plates in the rules are modified, and the safety coefficients are evaluated referring to the target reliability specification, then the more reasonable formula of assessing the slamming strength of bottom of the bow is given

    在上述工作的基礎上，對我國建造規范中原有的砰擊壓力名義值和底板承載能力名義值的計算公式進行了修正，並參照選定的目標可靠性指標求出了安全系數，給出了更為科學合理的船首底部砰擊強度定值評定公式。
  9. Composite string insulator units for overhead lines with a nominal voltage greater than 1000 v - part 1 : standard strength classes and end fittings

    額定電壓超過1000v的架空線用復合絕緣子串組合件.第1部分:標準強度等級和端接頭
  10. Composite string insulator units for overhead lines with a nominal voltage greater than 1000 v. standard strength classes and end fittings

    標稱電壓超過1000v的架空線用復合絕緣子串組合件.第1部分:標準強度等級和接頭配件
  11. The force transducers with a nominal load of 5kn and an overload withstand capability of up to 10kn, are designed with dynamic fatigue strength for several million load alterations

    額定負載為5 kn ，超載負荷能力最大為10 kn ，具有動態疲勞強度設計的力傳感器要可以承受多達幾百萬次的負荷變化。
  12. Aerospace ; hexagon bolts with waisted shank and mj thread, steel nominal tensile strength 1100 mpa, for temperatures up to 235 c

    航空和航天.帶mj螺紋縮頸標稱抗拉強度1100mpa
  13. Aerospace ; hexagon bolts with waisted shank and mj thread, titanium alloy, nominal tensile strength 1100 mpa, for temperature up to 315 c

    航空和航天.帶mj螺紋縮頸標稱抗拉強度1100mpa
  14. Aerospace ; bihexagonal head bolts, close tolerance, with mj - thread, medium thread length, in steel, nominal tensile strength 1800 mpa, for temperatures up to 235 c

    航空和航天.帶mj螺紋緊公差中等長度螺紋鋼制
  15. Aerospace ; bihexagonal head bolts, close tolerance, with mj - thread, medium thread length, in steel, nominal tensile strength 1550 mpa, for temperatures up to 235 c

    航空和航天.帶mj螺紋緊公差中等長度螺紋鋼制
  16. Aerospace ; bihexagonal head bolts, close tolerance, with mj - thread, medium thread length, in steel, nominal tensile strength 1250 mpa, for temperatures up to 235 c

    航空和航天. mj螺紋緊公差中等長度螺紋鋼制標
  17. Aerospace ; countersunk head screws, with ribbed torq - set recess and mj thread, short thread length, steel ; nominal tensile strength 900 mpa, for temperatures up to 235 c

    航空航天.抗拉強度900mpa使用溫度為235以下的鋼制短
  18. Aerospace ; pan head bolts with ribbed torq - set recess and mj - thread, short thread, steel, nominal tensile strength 900 mpa, for temperatures up to 235 c

    航空和航天.帶mj螺紋短螺紋鋼制標稱抗拉強度90
  19. Aerospace ; pan head bolts, close tolerance, with ribbed torq - set recess an mj - thread, short thread, steel, nominal tensile strength 900 mpa, for temperatures up to 235 c

    航空和航天.帶mj螺紋短螺紋鋼制標稱抗拉強度90
  20. Post insulators for switchgears and substation with nominal voltages greater than 1000 v ; co - ordination of the definitions for mechanical bending strength

    公稱電壓1kv以上轉換開關設備和變電站用柱形絕緣子
分享友人
分享到 Line

分享到臉書