out-of-gearing 中文意思是什麼
out-of-gearing
解釋
脫開的-
As a new type gear transmission, double circular arc profile bevel gearing carries out its transmission by means of meshing between convex - concave tooth profile in both of the direction of tooth trace and the direction of tooth depth, so it has advantage of high load capacity, long service life, easy forming hydrodynamic oil film between teeth as well as high quality of running - in etc. therefore, more attention has been paid to its application and research in recent years
作為一種新型齒輪傳動方式，雙圓弧弧齒錐齒輪傳動不論在齒線方向、還是在齒高方向，均為凸、凹齒廓相嚙合，因而它比一般的弧齒錐齒輪傳動的承載能力高，使用壽命長；並且在嚙合過程中兩齒面間容易形成潤滑油膜，具有良好的跑合性能，所以對它的應用和研究日益受到人們的重視。 -
And with the software pro / e, the research carried out the molding and assembling of the gearing parts. secondly, according to the rotary error theory, this paper discusses the influence that the side - crack have on the rotary errors and reveal three kinds of rotary errors ( intrinsic errors, assembling errors, other errors ) that may come out in the gear drive
其次，利用回差分析理論分析側隙對回差的影響和齒輪傳動中可能出現的三類回差來源（齒輪本身的固有誤差，裝置誤差，其它誤差） ，並詳細計算了各級傳動中的回差的大小，檢驗結構精度分配的正確性，提出減小回差的措施。 -
Finally, by means of comparing the theoretical tooth surface equation with the tooth surface equation included errors of cutter position and cutter position angle, the quantitative analysis of the theoretical tooth shape and the tooth shape considering the errors of cutter position and cutter position angle was curried out based on the software above. from which, the effect of errors of cutter position as well as cutter position angle on the processed tooth shape and transmitting behavior of this kind of gearing was studied
最後，通過比較雙圓弧弧齒錐齒輪齒面理論方程與加入刀位及刀位角誤差后的齒面方程，應用上述軟體和通過進一步的數值計算，進行了無誤差的理論齒形與加入刀位及刀位角誤差后所得到的實際齒形之間的定量分析，比較直觀、方便、準確地對刀位及刀位角誤差對雙圓弧弧齒錐齒輪的齒形以及傳動的影響進行了初步研究。 -
Delay is obvious in large body because of its inertia, moment force, stress and gearing. transfer of electical cell increases the delay. this paper points out that the delay can be compensated by using the smith control algorithm. the result of computer emulation proved that a better quality is gained by using the algorithm on heavy nc machine
大慣量物體，由於其慣性，加之傳動鏈長，所需的扭矩大，引起的應變大，加上電氣轉換元件的滯后，故滯後效應明顯.該文提出用史密斯控制演算法將滯后進行補償.計算機數字模擬結果說明，對大慣量有滯后的重型數控機床，應用該演算法能得到較好的控製品質 -
According to the characteristics of spatial - cycloid - ball gearing, meshing transmission theory is studied and related numerical simulation is carried out. major contents are as follows : 1
本文根據新型空間凸輪活齒精密傳動的特點，研究了嚙合傳動理論，並進行了相應的數值計算。 -
The robot compounds vision signal and sensor signal observed by itself, and transmits them to the computer far away. the powerful computer, then, analyses and deals with them, sends out signal to gearing of the robot to control its action in succession. or the robot just does some low - end work such as avoiding blocks, and other work will be done by the powerful machine in the distance or manual work in virtual environment via remote control : to apply the technique of virtual reality to the research of navigation of mobile robots is a feasible method
因此，將計算機和機器人分開，機器人把觀察到的視覺信號和傳感器信號，按照制定的標準合成，然後傳送到遠方計算機上，由功能強大的遠方計算機進行分解和處理，並發出控制信號給機器人的傳動機構以控制機器人行為，或者由機器人完成一些避障類的低層操作，而高層操作由遠方高性能機器、或人工在虛擬環境中遙控完成：將vr技術應用到移動機器人導航研究中將是一種可行的方法。 -
In this dissertation, first, based on the theory of w - n gearing, characteristic of tooth profile as well as the processing principle of helical bevel gear, a cutting meshing analysis about double circular arc profile bevel gear was carried out, the equation of meshing in the process of cutting tooth, the surface equation of generating gear as well as the general tooth surface equation of double circular arc profile bevel gear were obtained
本論文首先根據雙圓弧齒輪傳動的嚙合理論，結合其齒形特點和弧齒錐齒輪的加工原理，進行了雙圓弧弧齒錐齒輪的切齒嚙合分析，得到了切齒嚙合過程中的嚙合方程、產形輪齒面方程以及雙圓弧弧齒錐齒輪的通用齒面方程，為下一步生成雙圓弧弧齒錐齒輪的三維模型打下了基礎。 -
Generally analyses vibration signals of gearcase in some roiling mill by using various spectrum analytical methods ( such as zoom apectrum and cepstrum ), and finds out that source of exceptional vibration is owing to imbalance of the whole gearing. through assembly adjusting and carrying out dynamic balance test finally solves problems of production practice and ensure that the product line is put into production on schedule
摘要利用各種頻譜分析手段（細化功率譜和倒頻譜）對某軋鋼廠齒輪箱振動信號進行了全面分析，發現整個傳動裝置產生的不平衡導致齒輪箱振動異常，經過裝配調整，並做了動平衡試驗，有效地解決了這一問題。 -
So this paper bring forward several new concepts and new terms, and give the whole defmations to their physical meanings ; advance the conditions of right gearing mesh and continuous drive ; prove out that a pair of ring involute tooth forms are conjugated and that they can achieve precise spherical motion of constant transmitting ratio employing the space mesh theory
為此，本文首次提出了球齒輪傳動中若干新概念，新名詞，並對物理含義作了完整的定義；提出了球齒輪機構的正確嚙合條件和連續傳動條件；利用空間嚙合理論，證明了一對漸開線環形齒廓互為共軛齒廓，能實現精確的定傳動比球面運動。 -
Through analysis the reasons influencing measuring stability have been found out, which are the flexure strain and structure resonance produced by the transmission axle under the function of the gearing - in force of the reduction gear
雖然與傳統的測量方法一致，但經過理論分析，得出了這種測量方式機械結構影響測量穩定性的原因，即傳動軸受減速器齒輪嚙合力作用?生的彎曲應變和結構諧振對測量精度影響最大。
分享友人