power inductance 中文意思是什麼

power inductance 解釋
電力電感
  • power : n 1 力，力量；能力；體力，精力；（生理）機能；〈常 pl 〉才能。2 勢力，權力，權限；威力；政權；權...
  • inductance : n. 【電學】電感，感應現象；感應系數；（發動機）進氣。 inductance bridge 電感電橋。
  1. This device realizes series resonance between high voltage inductance and tested capacitance. because of series resonance a higher voltage exists on the tested capacitance than the power ' s output. so a new ac high voltage test way to large capacity sample comes true

    該裝置以調頻的方式實現高壓電感和被試品電容的串聯諧振，從而在被試品上得到高於電源輸出端的電壓，即實現了以小容量電源對大容量試晶進行交流耐壓試驗的一種新方法。
  2. According to the quickly adjustable characteristic of the peterson coil grounding system, this dissertation proposes a new control strategy. when the system is in operation, the strategy can limit the series resonance over - voltage by using the off - resonance method. when fault occurs, the strategy can conveniently suppressing arc by rapidly adjusting the inductance value of the peterson coil to the point, which the resonance with grounding capacitance of the power network is occurred

    依據可控硅控制消弧線圈接地系統的快速可控性，一改傳統的電網正常運行時調節消弧線圈接近於全補償的預調諧方法，提出正常運行時採用脫諧方法抑制串聯諧振過電壓；故障時立即調節消弧線圈電感量達到與對地電容諧振，以利熄弧的新型調節原理和方法。
  3. This article has studied the deficiency and shortcoming of various kinds of methods of the parameter measurement of transmission line at present, proposed the measurement under operation on the basis of gps, researched gps application way and error that may appear in the power system synchronal sampling, put forward the parameter computing technology based on the information of both sides of transmission line, which solved some problems that exist in the parameter measurement, especially the problem that exist in the zero - sequence parameter measurement of transmission line with mutual inductance

    本文研究了目前輸電線路參數測量的各種方法，分析了其中存在的不足和缺點，提出了基於gps的輸電線路參數在線測量方法，研究分析了gps在電力系統同步采樣中的應用方式以及可能出現的誤差，在同步采樣的基礎上提出了基於雙端信息的線路參數計算方法，較好地解決了輸電線路參數測量中存在的一些問題，尤其是多回互感線路零序參數測量困難的問題。
  4. Big power inductance load ups : theory and application of gerqui wave

    金魁波電源的理論和實踐
  5. With the advance of semiconductor manufacturing, circuits with increasingly higher speed are being integrated at an increasingly higher density, which makes analysis and verification of power grid integrity more important. power grid integrity includes four issues, namely, ir drop analysis, ground bounce analysis, ldi / dt from the pin inductance and em analysis

    隨著超大規模集成電路集成度和工作頻率的不斷提高，電源網格完整性分析變得越來越重要，一般有四個關鍵問題： ir電壓降分析、接地點電勢上升（ groundbounce ）分析、來自引腳電感的ldi / dt分析和電子遷移率em分析。
  6. Phase - shifted zero - voltage - switching pwm full bridge converter can realize zvs for the power switches with the use of the leakage inductance of the transformer and the intrinsic capacitors of the power switches, so it is used widely for medium and high power applications

    移相控制零電壓開關pwm全橋變換器利用變壓器的漏感和開關管的結電容可以實現開關管的零電壓開關，在中大功率的場合應用廣泛。
  7. The control motors in the well traction robot require high temperature resistant, quick response, small volume and large power density. because coreless dc motors uses ironless - rotor, the inertia and inductance is very small, mechanical time constant is less than 28 milliseconds, several products can attain in less than 10 milliseconds. its weight and size are 1 / 3 - 1 / 3 less when compared with an iron core motor of same power

    水平井牽引機器人對控制電機不僅有耐高溫要求，而且有響應快、體積小、能量密度大等要求，而空心杯電樞直流電動機由於無鐵心，故慣量和電感均大為減小，機電時間常數小於28ms ，部分產品可以達到10ms以內;與同等功率的鐵芯電機相比，其重量、體積減輕1 / 3 - 1 / 2 ，是低慣量電機中性能最好的一種。
  8. Zero - voltage turn - on and zero - voltage turn - off in lagging arm and leading arm of soft - switching topology, working waveform of power transformer and process of rectifier and transition are presented in detail. the influence of resonant inductance of the power transformer, resonant capacitor and variation of load to the process of soft - switching are given

    主要對軟開關滯后橋臂和超前橋臂的零電壓開通、關斷過程，功率變壓器的工作波形及整流換流過程進行了詳細的模擬分析，並重點討論了逆變器的諧振電感、諧振電容以及負載變化對軟開關過程的影響。
  9. Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting ". under the condition of constant diameter of welding wire and its feeding speed, the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply. if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition, the welding process will be stable with less spatter and smooth weld bead

    通過分析不同焊接規范下的焊接電壓和電流的波形.研究了水蒸氣保護下電弧及熔滴過渡的特點，發現其電弧過程行為有「燃弧?熄弧?短路」和「燃弧?短路」兩種形式.在焊絲直徑和送絲速度一定的情況下，通過調節焊接迴路中的電感量和電源電壓，可以改變電弧的過程行為形式.若電弧過程呈「燃弧?熄弧?短路」交替進行，並且熄弧時間最短時，短路過渡頻率最高，在這種情況下，飛濺小，焊道成型好，焊接過程穩定
  10. The main products are 35kv - 200kv capacitance casing porcelain cover, mutual inductance porcelain cover and middle - small sized power station, electrical equipment, route electrical porcelain for five category 30 series and 300 kinds

    企業具備多年生產高壓瓷套的經驗和一批熟練的技術工人，以及完善的公用設施。同時，本地能源充足價格較低。
  11. The control tactics of space voltage vector are investigated, and the simplified algorithm which judges the sector location of reference vector and calculates switch operation time is put forward. by analyzing the current hysteresis control, the relation between switch frequency, and hysteresis bandwidth and input inductance of pwm rectifier is deduced. by applying instantaneous power theory, the principle of pwm rectifier power control is analyzed, and the direct power control by matlab toolbox through estimating active power and reactive power with virtual flux is realized, and the simulation results prove that it is correct

    對常用空間電壓矢量控制策略進行分析，提出了給定參考矢量所在區間判斷的簡化方法，以及電壓矢量作用時間的求取方法；分析了電流滯環控制策略，推導出開關頻率與滯環帶寬以及整流器輸入電感之間的關系；應用瞬時功率理論分析pwm整流器功率控制原理，通過虛擬磁鏈估計有功功率和無功功率，用matlab實現了直接功率控制，並驗證了該控制方法的正確性。
  12. In chapter 4, considering the features of high voltage transformer and the difficulties to make it, a reasonable design scheme with src was proposed, which efficiently reduced negative influence of distributing parameters of transformer on switching power supply and could completely utilize leakage inductance as resonant inductance

    第四章中分析了高頻高壓變壓器的特點及難點，提出了合理的串聯諧振變換器的設計方案，能夠完全利用變壓器的漏感作為諧振電感，有效地降低了分佈參數給高壓大功率開關電源所帶來的不利影響。
  13. The sieries product is suitable for the system with current 50hz - 60hz and the rated voltage of 3. 6kv 40. 5kv. it can be matched with other protective electrical equipment vacuum connection, loading switch etc. it can also be used as the overload or short circuit protection parts for high voltage motor, transformer, voltage mutual inductance attenuator and other power equipment

    本系列產品適用於交流50hz - 60hz ，額定電壓3 . 6kv 40 . 5kv系統，可與其它保護電器如真空接觸器，負荷開關等配合使用，作為高壓電動機電力變壓器電壓互感器及其它電力設備的過載或短路保護等元件。
  14. The basic idea is that increasing the equivalent harmonic impedance of power network by valid control of active filter, in order to enhance the performance of passive filter and damp the resonance between the passive filter and the equivalent inductance of the power network

    無源支路在補償無功功率的同時還可以濾除因非線性負載產生的特徵諧波電流，為了抑制無源支路跟電網等效電感產生的諧振現象以及改善無源濾波器的濾波性能，系統中採用諧振注入式有源濾波拓撲。
  15. By compared with the simulation results and the experiment results, we come to the conclusions that : ( 1 ) circuit with assistant network can widen soft - switching extent in lagging arm, reduces duty - cycle loss on the secondary, diminishes switching dissipation of inverter spot - welding power source. ( 2 ) the range of resonant capacitor, the important factor to soft - switching process, not only affects zero - voltage turn - off of power switches, but also affects the range of zero - voltage turn - on of power switches. so resonant capacitors must be considered according to many aspects ; ( 3 ) it easily fulfils soft - switching condition in lagging arm as leakage inductance of power transformer increases, but bigger leakage inductance of power transformer increases opening dissipation of transformer and decreases efficiency of soft - switching inverter power source

    通過模擬結果與軟開關點焊逆變器試驗結果的對比分析，得到了如下主要結論：採用輔助網路可以完全拓寬全橋軟開關逆變器的滯后橋臂軟開關范圍，減小了次級占空比丟失，降低了逆變電阻點焊電源的開關損耗；諧振電容是影響軟開關工作狀態的重要因素，其大小不僅影響開關管的零電壓關斷，同時也影響開關管的零電壓開通范圍，因此，諧振電容應該綜合考慮；功率變壓器漏感越大，越容易滿足滯后橋臂的軟開關條件，但是大的漏感也使變壓器的通態損耗增加，降低了軟開關逆變器的效率。
  16. Because of the clamping capacitor and the interleaved structure, it has some good features compared with other flyback converters, such as : the topology is simple and can be realized easily ; the voltage spike of the power switch is availably restrained and without leakage - inductance energy loss ; the ripple of the input and output current is reduced, correspondingly, the volume and weight of the output and input filter is also significantly reduced

    由於箝位電容的加入，相對于其他類型的反激式變換器電路，該拓撲具有一些獨特的優點:電路結構簡單且易於實現;無需另加輔助開關管，實現了開關管的有源箝位，抑制了開關管的電壓尖峰;提高了輸入、輸出電流的脈動頻率，減小了輸入及輸出濾波器體積。
  17. A new viewpoint to observe the relation of bus voltage, bus current injection and branch current of the network considering branch mutual inductance has been provided in this paper. the process of building the z - matrix of a large - scale power network is set forth in particular in this paper. and the method is employed in the fault computation system successfully

    本文為了從演算法上提高故障計算的速度，在完全計及支路互感的前提下，利用節點注入電流與支路電流以及支路電流與節點電壓的關系，提出了一種能夠統一處理互感和無互感線路、快速形成大規模電網節點阻抗矩陣的新方法。
  18. The system can generate sweep frequency signal with frequency range from 100khz to 150mhz and power range from - 40dbm to + 18dbm, and measure the gain and phase of the crystal. according to the gain and phase information and the iec - 444 standard, crystal parameters can be calculated, such as nominal frequency, series resistance, shunt capacitance, motion capacitance, motion inductance, q factor and so on

    該系統能產生頻率范圍達100khz 150mhz ，功率范圍為? 40dbm + 18dbm的掃頻信號，並能對晶振的增益和相位差進行測量，其測量結果按照iec - 444晶振測量標準進行實時處理和計算，從而得到晶振的串聯諧振頻率、並聯諧振頻率、等效電阻、靜態電容、動態電容、動態電感和品質因數等主要電參數。
  19. Then this article analyzes the way to obtain the power of measuring device. also it recommends two kinds of feasible schemes of mutual inductance power and solar power, and proposes a power supply scheme that is called " the optic fiber supplying power " in the paper. the feasibility of this scheme is also analyzed here

    文章接著對測量裝置的電源獲取途徑進行分析，介紹了互感供電和太陽能供電兩種可行的方案，並提出了本文稱之為「光纖傳光供電」的供電方案，具體分析該方案的可行性，並設計了該方案的主要組成部分解決了中高壓系統參數測量中的兩個共同問題以後，文章設計了中高壓系統溫度在線監測裝置。
  20. A novel resonant pole zvt three - phase pwm inverter circuit for three - phase ac motor driving is presented. the proposed circuit has the feature of being more flexible with three inverter arms in zvt process. using only one resonant inductance, the inverter can not only reduce the power loss of inductance but also avoid possibility of unbalance in motor ' s three stator windings

    提出了一種針對三相交流電機驅動的新型諧振極零電壓過渡三相pwm逆變器電路，該電路中三個逆變橋臂的零電壓過渡更具有靈活性，僅使用一個諧振電感，既減少了電感損耗又防止了電機三相定子繞組可能存在的不平衡問題，並且諧振電感中殘余能量能夠回饋給電源；新型逆變器的輔助開關均工作在零電流開關條件下，並且控制邏輯簡單。
分享友人
分享到 Line

分享到臉書