revolution surface 中文意思是什麼

revolution surface 解釋
回轉面
  • revolution : n 1 革命；劇烈的變革。2 回轉，繞轉，旋轉；轉數；周期；一轉；【天文學】運行，周轉，公轉。n ism 革...
  • surface : n 1 表面；地面；水面；廣場，空地。2 外觀，外表，皮毛。3 【幾】面；切口；【航空】翼面。adj 表面的...
  1. The pivot and race surfaces were true surface of revolution and were correctly centered when no load was applied.

    軸樞和套圈的表面是準確的旋轉表面，並在未施加載荷正確對中。
  2. Integration formula for calculating the area of the curved surface of revolution

    計算旋轉曲面面積的定積分公式
  3. If the graph of a continuous function is revolved about a line, the resulting surface is called a surface of revolution

    一個連續函數的圖形繞一條直線旋轉所得到的曲面為旋轉曲面。
  4. Surface of revolution is very common in industry models

    旋轉面是工業產品中常見的一種外形。
  5. So the reconstruction of surface of revolution becomes a necessary task in reverse engineering

    進行旋轉面的重建，是反向工程中的一個必不可少的課題。
  6. In this paper, we take the reconstruction of surface of revolution as our main aim, and by using the delaunay triangulation, the definition of curvature and the theory of b - spline, we present a way of reconstructing surface of revolution from point cloud. the main content of this paper is given in the following. computer aided geometric design and reverse engineering are the basis of this article

    本文以旋轉面重建演算法為主要研究對象，應用三角部分、曲率的定義以及b樣條理論提出了一種由點雲數據構造旋轉面的方法，主要工作如下：計算機輔助幾何設計以及反向工程是本文的理論基礎，因此論文的第一章對其進行了簡短的回顧和綜述，並給出了旋轉面重建演算法目前的研究狀況。
  7. A ruled surface of revolution formed by an edged circle as the guide element is proposed in the category of basic geometrical bodies

    摘要在基本幾何體的范疇內，提出一種以棱圓為導元素的直紋曲面。
  8. In this dissertation, higher order anisotropic / tensor impedance boundary condition ( hotibc ) was derived and applied to anisotropic coated planar, cylindrical or bodies of revolution. the design of optimal ram for several conical targets was considered. the exact impedance for single and multilayer arbitrary material coated conducting planar and cylindrical surface were build hi spectral domain

    本文以各向異性介質塗敷結構為研究對象，研究各向異性阻抗邊界條件的導出和在平面及曲面結構上的應用方法和應用條件，最後，針對幾類典型體的ram進行優化設計，建立快速、有效的設計方法。
  9. The general tolerances on circular run - out ( radial, axial and any surface of revolution ) are given in table 4

    表4給出了圓跳動未注公差的（ 。 。 。 。 ？ ）括裏面的是什麼意思啊，多謝！
  10. ( 3 ) in co - revolution disc cavity, heat transfer coefficient which is high on most region of disc surface show that the co - revolution avails the heat transfer on disc surface

    （ 3 ）在共轉盤腔結構中，大部分區域盤面的換熱系數都較高，表明共轉狀態對盤面的換熱有利。
分享友人
分享到 Line

分享到臉書