rheology design 中文意思是什麼

rheology design 解釋
流變設計
  • rheology : n. 【物、化】(研究物質流動、變形、彈性、黏性、可塑性的)流變學;液流學。
  • design : vt 1 計劃,企圖,立意要…。2 指定,預定;留給,留著。3 設計,草擬,擬定,籌劃;起草,畫草圖,打(...
  1. A new method should be discovered to design the function block. the thesis is based on the rheology and hydrokinetics of the polymer melt, and calculates the velocity in the die by fem simulation, and provides die design with theory proof. according to the existed theory, i summarize and conclude the fem formula of the polymer flow, and then write the program to calculate on the computer

    本論文中功能塊結構的研究,是以熔體的流變性以及流體動力學理論基礎上,對在口模中的熔體進行數值模擬,計算出熔體在口模中的流動參數(主要是速度的分佈) ,從而可以科學的對功能塊幾何結構進行優化。
  2. Moreover, the main components of h mineral admixture is procured from industry waste, and its " production procedure is simple, so its " production cost is very low. the most tightness pile up theory and rheology is successfully applied in the designation of self - compacting concrete, and the factors such as sand rate, aggregate grading, paste content and mineral admixtures are been studied. under the guidance of mix design theory and on the basis of mass experiments, c20 - c80 high performance self - compacting concrete is been produced

    將最緊密堆積原理和流變學原理相結合,運用於免振搗混凝土配合比設計之中,系統地研究了砂率、集料級配、水泥漿量、礦物摻合料等因素對免振搗混凝土物理力學性能、工作性能、耐久性能的影響,成功配製出從c20 - c80及以上強度等級的高性能免振搗混凝土。
  3. The sofware design of drilling fluid rheology parameter automation detect system

    鉆井液流變參數自動檢測系統軟體設計
  4. Based on theory of gear driving, fluid mechanics, hydrodynamic lubrication, polymer rheology and single - screw extrusion, key structure design principles in melt pump are summarized, some theory foundations are also deduced

    結合齒輪傳動、動力潤滑、流體力學、高聚物加工流變學以及單螺桿擠出理論的部分知識對熔體泵結構設計中的主要問題進行了總結,並對其中部分理論依據進行了推導。
  5. On the basis of analyzing mechanism of magneto - rheology, some models used to characterize mr effect have been summed up in the second chapter. the reasons, which influence mr effect and sedimentary stability of mr fluids, etc. are analyzed according to models above - mentioned. the mr fluids used to develop automotive mr dampers in this dissertation have been comprehensively tested for the damper design purpose by means of the magnetorheology - meter offered by < wp = 7 > department of engineering mechanics of chongqing university

    介紹了磁流變效應的流變機理和磁流變效應的模型描述,並利用描述模型分析了影響流變學性能的各種因素,提出了用於汽車磁流變阻尼器的磁流變體的性能要求;介紹了磁流變體的性能測試原理,利用重慶大學力學系研製的磁流變測試儀器對八種磁流變體的bingham模型參數進行測試,為磁流變阻尼器設計計算提供材料參數和結構設計中的技術問題處理提供依據。
  6. Workability - design of fresh concrete was studied from rheology aspect. mortar slump flow test was further developed to evaluate properties of water - reducers and compatibility between cement and water - reducer for mortar. a method for measuring water absorbed by coarse aggregate in fresh concrete was put forward

    從流變學角度對新拌混凝土工作性進行了以下研究:進一步完善了砂漿坍落擴展度試驗方法,用於測評砂漿中減水劑飽和摻量及水泥對外加劑的適應性。
  7. In this paper, a new generation pressure sensor type rheology instrument is researched ; and the design principles of both hardware and software are described in detail

    本課題主要研究新一代的壓力傳感式血流變儀。論文詳細闡述了該儀器從硬體到軟體的設計原理和實現方法。
分享友人