sandwich system 中文意思是什麼
sandwich system
解釋
夾層鋪築法-
On the basis of the experimental research, its hysteresis characteristics, calculation method of stiffness in different stage and ultimate bearing capacity are discussed. based on a seismic design method on the new lateral resistant system is concluded according to the research result in the paper. the effect of some parameters is discussed on steel frame with cavity sandwich wall infill and some design suggestion is presented
在試驗研究的基礎上，建立了該體系的恢復力特性模型，提出了模型各受力階段的剛度計算公式、極限承載能力的計算方法和抗震計算方法；對影響空腔結構砌體填充墻鋼框架抗側力性能的因素進行了討論，提出了設計建議。 -
Making report forms in distributed sandwich - like structure application system
分散式多層應用系統報表製作 -
Sandwich seismic wall which concrete column was replaced with angle - steel truss was discussed in this paper in order to be used as outer - walls of multi - story shear walls system
本文研究的是以角鋼桁架代替混凝土暗柱的夾芯保溫混凝土抗震墻，以下簡稱復合墻板。目的是用作小高層剪力墻體系的外墻。 -
The former consists of sandwich panel and frame structure, becoming light weighted frame slab structure. in this system the frame and the sandwich panel together resist horizontal and vertical loads
有骨架體系由夾芯板與框架結構組合而成，形成框架輕板建築，框架與夾芯板共同承受水平和垂直荷載。 -
To eliminate or lessen the system errors caused by the offset and slope of the thin aluminum sheet when measuring its surface, and to avoid over - cutting while machining the honeycomb surface, the saddle - point programming is applied to the position optimization of the theoretical surface. to generate the cnc program of the honeycomb sandwich, the equidistant calculation of the actual surface is produced and the data processing software is developed
利用鞍點規劃方法優化理論橢球面的位置，使實測曲面相對理論橢球面的最大法向誤差達到最小，減少或消除了蒙皮內表面測量時由於定位的偏心或歪斜引起的系統誤差，使誤差均化，防止了配對加工蜂窩夾芯表面時少切或過切現象的發生。 -
First, according to the demand of vimp for resin system, the reaction kinetics and rheological of up resin are investigated and the optimal content of low additive profile ( lpa ) is determined. then vimp based on a high - permeable medium and grooves are studied by visual experiments, through which the appropriate high - permeable mediums are selected and the parameters of width, depth and spacing for flow grooves and spacing for supply grooves are optimized. furthermore, various factors affecting the mold filling process are discussed and the whole vacuum infusion procedures are described taking examples of the manufacture of a model boat and a sandwich panel in one infusion
文中首先根據vimp對樹脂體系的要求，對vimp用不飽和聚酯樹脂體系的動力學和流變學性能進行了研究，確定了最佳低收縮添加劑的含量；對高滲透介質型和溝槽型vimp開展了實驗研究，通過可視化實驗優選出較好的高滲透介質，確定了引流槽的寬度、深度和槽間距及主槽的槽間距等工藝參數並進行了優化；對影響充模過程的各種因素進行了詳細的討論，並以模型船和夾芯面板的製作為實例描述了兩種vimp的成型過程；在實驗的基礎上，建立了二維滲漏模型，採用控制體有限元法對高滲透介質型vimp進行了成型過程的計算機模擬計算，通過充模時間和流動前峰的計算值與實驗結果的比較，驗證本文所採用的數學模型和數值方法的正確性，其結果對實際生產具有一定的理論指導意義。 -
Light weighted reinforced concrete multi - rib sandwich slab structure system is a kind of new system, which can entirely replace the brick composite system to be adapted to the policy of wall materials reform of our country
輕質鋼筋混凝土夾芯板建築結構體系是適應我國墻改政策、可以完全取代磚混體系的一種新型結構體系。 -
The principal needs of realization on strategic inertial accelerometer are large measurement range ( higher than 70g ) and high stability. in this paper aimed at a most basic and typical " sandwich " structure with easy realization in techniques, the system of micromachined electrostatic servo - accelerometer is analyzed in detail on static and dynamic state, mainly including : the influence on the z - component of the center of mass, lateral accelerations disturbance and the applied bias voltage on the stability of the sensor
戰略慣導加速度計實用化的首要條件是大量程（ 70g以上）和高穩定性，本文針對一種最基本、最為典型和工藝上較易實現的「三明治」結構，從靜態和動態兩方面對電容式微機械靜電伺服加速度計系統進行了詳細分析。 -
There are still many problems remain to be solved in these aspects, such as research on the cladding material, lateral resistant system and steel frame connections, etc. in this paper six 1 : 2 - scale steel frame specimens and eight full - scale steel frame connection specimens are tested on their behavior under cycle loading. there are five aspects as below on the problems of steel resident building researched : 1 a new lateral resistant system, which is steel frame with cavity sandwich wall infill, is put forward for the first time in this paper
本文針對鋼結構住宅體系中亟待解決的若干問題，完成了六榀1 : 2鋼框架模型試驗和八個足尺比例的樑柱連接模型在低周往復荷載作用下的試驗，進行了以下幾個方面的深入研究： 1本文首次提出了一種新型的空腔復合填充墻鋼框架抗側力體系。 -
Standard specification for epoxy resin system for composite skin, honeycomb sandwich panel repair
合成革蜂窩狀夾層板修補用環氧樹脂系統標準規范 -
Multi - agent based information management in the software project is also one part of the study with the communication language - knowledge query and manipulation language. at last, construction and application of sandwich agent in work quantity wbs / communications mechanism of multi - agent cooperation system in tender offer and bidding have been done
本文最後將基於agent的軟體開發項目管理方法應用於實際科研課題中，進一步研究了層次型agent在工作分解結構中的構建及應用，並在基於agent的項目信息管理的基礎上，對多agent協作系統應用在建築工程招投標時的kqml通信機制深入研究。
分享友人