screw wheel 中文意思是什麼
screw wheel
解釋
螺旋齒輪, 斜齒輪-
3 please screw down safety screw before installation, and screw down the component of pawl and rolling wheel anticlockwise according to opening direction of fingernail axis
3安裝前請退出保險螺絲，按爪軸的開口方向將棘爪與滾輪組合件按反時針方向退出。 -
Mc nylon boasts of fatigue - proof, anti - impact and abrasive resistance etc. it has been successfully applied on straight gear, worm wheel, bevel wheel and screw gear for 25 years
Mc尼兼有耐疲勞抗沖擊和耐磨等性質，使其在輪應用上極受歡迎，已成功地應用在直輪蝸輪斜輪和螺旋輪上有25年的歷史。 -
Abstract : by means of metallographical examination and sem, the microstructure characteristics, macro - and microfractographs of the brittle broken wheel hull bolt of bj212 automobile have been studied. the results show that the thin - headed screw, with excessively deep carbonitriding layer and hardening layer, has less resistance to brittle fracture in the thin area of its head. at the root of the head connecting the stem, a tensile stress may emerge owing to the non - even quenching stress. those are the two reasons for low torque fracture of bolt
文摘:藉助金相、掃描電鏡等手段對低扭矩脆斷的bj212汽車輪殼螺栓的金相組織特徵，宏觀和微觀斷口形貌等進行了研究，結果表明：這種頭部薄的螺栓，滲層和淬透層過深，使頭部薄區脆斷抗力降低，在頭部與桿的根部，由於淬火應力不均勻導致根部產生拉應力，均是導致螺栓低扭矩斷裂的原因。 -
The company ' s main products include : ordinary - type, forward - and - backforward - thread typeandcalibre - changed type, three series and 50 - odd varieties of steel straight thread connecting sleeve piece and steel straight thread screw rolling machine, screw rolling wheel, cutting tool, reinforced thread head special gauge, moment spanner ect., auxiliary tools which are used in construction
公司主要產品有標準型、正反絲型、變徑型三大系列五十多個品種的建築用鋼筋直螺紋連接套筒和鋼筋直螺紋（剝肋）滾絲機及滾絲輪、切削刀具、鋼筋絲頭專用量規、力矩扳手等輔具。 -
Abstract : discusses the mechanical servo system with ball screw and linear motion guide assembly to measurement of the great wheel, and analyses the influence of the rigidity of transmission system on the accuracy
文摘:介紹了以滾珠絲杠與滾動導軌副為主體的機械伺服系統在大型輪式零件尺寸綜合測量中的應用，並分析了傳動系統剛度對測量準確度的影響。 -
Hang door sheet and install the localization screw on the lifting wheel
7掛門鈺並安裝吊輪上的定位螺絲。 -
Hang door sheet to adjust every level the screw in lifting wheel is adjustable. check the lock and push the door to make sure it is slippery
掛門鈺調整各門鈺的水平吊輪上有螺絲可調節，檢查鎖具能否鎖上，趟動門鈺感覺是否順滑。 -
Forget to put the locating screw in lifting wheel
忘裝吊輪上的定位螺絲。 -
Aiming at the design requirements of shield tunnelling machine for simulator test rig, hydraulic systems of shield were designed and manufactured by applying electro - hydraulic proportional control technology, which included thrust hydraulic system, screw conveyor hydraulic system and cutting wheel drive hydraulic system
摘要針對盾構掘進機模擬試驗臺的設計要求，採用電液比例控制技術設計製造了盾構掘進機液壓系統，包括推進液壓系統，螺旋輸送機液壓系統以及刀盤驅動液壓系統。 -
The structure of the wheel is divided into two parts, the superstructure and infrastructure. the upper penetrates the cartons and fixes the lower through the screw
輪子的結構分為上下兩部分，上部穿透紙箱后與下部車輪通過螺絲固定。 -
The main reason is as follows : dust in lifting rail is not removed clean ; lifting rail is not at a level ; the installation of low locator is not correct ; regulate screw in lifting wheel regulates too high
趟動門鈺感覺不顧滑，主要原因有：吊軌里的灰塵沒清除干凈吊軌不夠水平下定位安裝不準確和吊輪調節螺絲調節過高造成。 -
This machine adopts plc control system shows width and speed, it adopts electromagnetism to control the motor which adjusts width, double screw rod and double straight line rolling glide transmit, five grinders at each side, three are coarse and fine grinding, two are polishing according to customer s require to collocate the wheel, which can be used to process 3mm to 8mm small flat glass and pencil edge
詳細說明：本機採用plc控制系統顯示寬度和速度，採用電磁製動機調節寬度，雙絲桿和雙直線導軌傳動，單邊五個磨頭，三個粗精磨，兩個拋光可按客戶要求配套磨輪。適用於加工38mm的中小片玻璃的平邊和圓邊。 -
The front earth pressure value could also be controlled in the range of set value by adjusting the advancing speed, screw conveyor revolving speed and cutting wheel revolving speed, which lead to reduce ground deformation
通過實時調節控制推進速度、螺旋輸送機轉速以及刀盤轉速，可以控制正面土壓力在設定范圍內，從而有效減少地表變形。
分享友人