semi solid 中文意思是什麼
semi solid
解釋
半固體-
4. after continuously heated and isothermally soaked, the equiaxed grain, as the result of the recrystallization, was the necessary texture condition of the semi - solid grain ' s globalization processing
4 、連續升溫和等溫保溫過程中再結晶形成等軸晶，為半固態晶粒球狀化提供了必西安理工大學碩士學位論文要的組織條件 -
The semi - solid recrystallization velocity was run - up when the holding temperature risen and the heating velocity accelerated. 5
保溫溫度升高和連續加熱速度加訣都會使半固態再結晶的速度提高。 -
Semi - solid forming of aluminum is finding its main niche today in its growing ability to 1 ) control metal viscosity and hence mold filling behavior, 2 ) reduce die casting cycle time, 3 ) improve die life, 4 ) improve casting soundness and quality, and 5 ) produce parts at acompetitive cost
由於鋁半固態成型技術能更好地1 ）控制金屬粘性和模具填充性能2 ）減少壓鑄生產周期3 ）增加模具壽命4 ）改善壓鑄質量5 ）使生產的零件價格具有競爭性，因此目前有重要的使用價值。 -
The computer simulation results showed that the effects of ingate dimension and ingate location on the rheo - diecasting were relatively small, and the casting process - design was easily to be done ; under the same condition, the semi - solid rheo - diecasting decreased the air entrapment during the mould filling process, and high quality metal castings could be obtained through semi - solid forming technology
結果表明：半固態流變壓鑄成形在不同的內澆口尺寸與位置條件下都可以獲得平穩的充型流動場，其工藝參數設計靈活；同等條件下，半固態流變壓鑄成形的型腔充填過程平穩，成形鑄件的質量優于液態壓鑄成形。 -
Abstract : in this study, 2618 aluminum alloy manufactured by spray process was heated in a heating furnace, and the microstructures were investigated. by the process of heating in a heating furnace and then squeeze - forming, one component of the motorcycle was produced successfully with the semi - solid aluminum alloy
文摘:採用電阻爐加熱的方法對噴射沉積法制備的2618鋁合金進行了二次加熱實驗，觀察了顯微組織的變化；並通過電阻爐加熱、半固態擠壓鑄造的方法成功地試制了摩托車零件。 -
Numerical simulation on the semi - solid forming process of an impeller
葉輪半固態擠壓鍛造過程數值模擬 -
You don ' t earn a single cent here. every day we eat eggs and semi - solid food
在這兒你一分錢都賺不到每天就吃雞蛋和半流質食物 -
During the temperature fields, the results indicate that the processing parameters such as the extrusion velocity, casting temperature, perform preheating temperature, die preheating temperature and so on are important for the temperature fields besides the dwell time. they are must be in concordance each other to the deforming zone is in the quasi - solid state, and the stable semi - solid extrusion is implemented. during the deforming fields, the hyperbolic sine thermo - rigid - viscoplastic fem model is selected according to the forming feature of the process, and the variations of the stress - strain fields are studied
在溫度場的模擬中，模擬結果表明，保壓時間是影響製件成形質量的關鍵因素之一，擠壓速度、液態金屬澆注溫度、預制體預熱溫度和模具預熱溫度等工藝參數對溫度場的影響也很大，需進行參數之間的協調，只有當變形區內部始終維持準固態時，才能實現穩定的液-固擠壓成形過程；在變形場的模擬中，根據液態浸滲擠壓的成形特徵，選用了雙曲正弦剛-粘塑性有限元計算模型，研究了變形過程中應力應變場的變化規律，研究了模角對變形和金屬流動的影響及變形力的變化過程和其影響因素。 -
The thixoforming is suitable for the controlling semi - solid forming of iron and steel with high melting point
由於觸變成形工藝本身的特點，使其更適宜於鋼鐵等高熔點材料的半固態成形控制。 -
Effect of tic particle on grain growth of al alloy in the semi - solid state
顆粒對半固態鋁合金晶粒長大行為的影響 -
The desired microstructure for semi - solid forming is one free of dendrites, with the solid present in as spherical a form as possible and with minimum entrapped liquid
半固態形的理想結構是無晶枝，呈現的固體要盡可能為球形狀，且滯留液體盡可能少。 -
This paper presents an adaptive control for the semi - active suspension using the combination of mr damper and feedback neural networks. analyzing the mr damper, a smart actuator, chapter 3 gives the design of pre - amplifier of current, which provides the external magnetic field. and it discusses the additional nonlinear stiffness resulted from the transition of mr fluid from liquid to semi - solid or solid
在分析新型智能材料用做作動器的磁流變阻尼器特性的基礎上，本文給出阻尼器線圈的前置電流放大電路，並討論了因磁流變液體固液態之間的可逆變化而產生的懸架系附加非線性剛度。 -
Study on solidification microstructure characteristic of az91 magnesium alloy in semi - solid
91鎂合金半固態凝固組織特徵的研究 -
When it was soaked in the semi - solid temperature, the preformed texture was accompanied with the part high - energy - area melting. its presentations were the honey combs at the grain boundary and the pools in the grain. it was the essence condition that the semi - solid metal maintained the solid character and had the thixotropy
5 、形變組織半固態保溫過程中伴隨著局部高能區的熔化，表現為晶界蜂巢狀結構和晶內液池現象，這是半固態合金保持固相特徵並具有觸變性的基本條件。 -
Thixotropic behavior of a semi - solid alsi6mg2 aluminum alloy under cyclic shear deformation
2鋁合金循環剪切變形下的觸變行為 -
The resulting semi - solid mixture then flows homogeneously, figure 1, behaving as a thixotropic fluid with viscosity depending on fraction solid, morphology, shear rate and time
這樣最終形成的半固態混合物會均勻地流動（圖表1 ） ，並依據固體粒度、晶形、剪切速率及時間而形成粘性觸變液體。 -
Fluxes and cover gases are currently used for the melting and production processes, and semi - solid thixocasting is also used to lower the operation temperature ; but there still remain many problems
目前一般採用熔劑覆蓋法和氣體保護法熔煉生產鎂合金，或採用半固態射鑄成形工藝以降低作業溫度，但都存在著不少缺點。 -
And the microstructure, the hardness and the wear resistance properties of complicated parts had also been studied and analyzed. the results showed that under the same experiment condition, the semi - solid flow and deformation properties of the composites increased with the increasing of the sic particles " volume fraction which below 12 %, that he composite reinforced with different volume fraction of sic particles were die - cast into complicated parts successfully, that sic particles dispersed even more uniformly in their complicated parts, and that he complicated parts " hardness was better than the composites "
結果表明，在sic顆粒體積含量低於12的情況下， sic顆粒含量越高，復合材料的成型性能越好； sic顆粒增強鋁基復合材料能夠用壓鑄的方法制備復雜壓鑄件； sic顆粒在壓鑄件中分佈更為均勻，且呈單顆粒；壓鑄件的硬度比復合材料鑄錠的硬度高； sic顆粒增強鋁基復合材料的壓鑄件耐磨性高於復合材料鑄錠。 -
Formation mechanism of non - dendritic microstructures of semi - solid alloys prepared by scr process
技術制備半固態合金非枝晶組織形成機制 -
Preparations of semi - solid alloy with non - dendritic microstructures and mechanisms of formation of the structures
半固態非枝晶組織合金的制備及形成機理
分享友人