shear structural system 中文意思是什麼

shear structural system 解釋
扭動構造體系
  • shear : vt vi （sheared 〈古語〉 shore; shorn sheared）1 剪（羊毛等）；修剪（樹木）；剪（呢絨的）長毛。2 ...
  • structural : adj. 構造上的，結構上的，組織上的。adv. -ly
  • system : n 1 體系，系統；分類法；組織；設備，裝置。2 方式；方法；作業方法。3 制度；主義。4 次序，規律。5 ...
  1. This paper uses for reference with an example of frame - shear wall structure and studies the conceptual design and method for optimizationof structural system. through establishing frame - shear wall structure unisonous differential eguation and finding a result, the side shifting curve, moment and shear force distribution curve are obtained under inverted triangle load action on the frame - shear wall structure. after analyzing and comparing, the range of best rigid characteristics for such structure has be gotten

    本文結合框架-剪力墻實例，研討了結構體系的概念設計和整體優化方法。通過建立框-剪結構協同工作的微分方程及求解，得出框-剪結構在倒三角形荷載作用下的側移曲線、彎矩、剪力分佈曲線，經分析對比，得出框-剪結構最佳剛度特徵值區間。
  2. The prestressed continuous beam - arch composite bridges are a special structural system where the horizontal thrust of the arch rib is absorbed by a prestressed tie at deck level. in some cases, this type of structure is preferable because it does n ' t have the large thrust at the spring hi traditional arch bridges and the somewhat large bending moment and shear force in traditional beam bridges. as a result, the performances of the prestressing reinforcement can be efficiently utilized

    它利用拱肋承擔壓力，系梁預應力束抵抗拱端推力，吊桿及縱橫橋面系結構承受橋面荷載，既克服了傳統拱橋巨大的拱端推力，又改善了連續梁橋較大的彎矩和剪力的受力狀況，最大限度地發揮了拱梁混凝土和預應力鋼筋各自的特點，經濟效益顯著。
  3. It ' s an ideal structural system and has multi - earthquake resistance ability because of a great deal of slabs removed in floors above the transfer - story amended the lateral stiffness of the stories near the transfer - story. based on the available references, the five - spring line element, the three - spring line element and the multiple vertical - line - element model are introduced to model special column, beam and shear - wall, the relevant stiffness matrixes are deduced and the restoring - force models are gaven to deep into the elasto - plastic seismic characteristics of the structure. acording to the results of shaking table test and elastic finite element analysis, a new making model melhod is presented in which uses the linear and the nonlinear element and the assumption that the floor is infinitely rigid in different areas

    為進一步研究這種復雜高層建築結構的彈塑性性能，本文在國內外現有研究的基礎上，提出利用五彈簧桿元、三彈簧桿元及多豎線單元模型分別模擬空間柱、梁和剪力墻，推導了相應的剛度矩陣並給出了恢復力模型；結合試驗研究和精細有限元分析的結論，提出線性和非線性單元相結合，剛性樓板假定和彈性樓板相結合的建模方法，較好地解決了空間結構彈塑性分析中佔用計算機資源較多的問題；接力大型有限元分析程序? ? ansys ，在上述建模思路的指導下建立了結構的空間非線性分析模型，進行了空間三維彈塑性時程分析。
  4. Under the horizontal earthquake action and wind force, aim at " the pure frame structure with rectangle columns ", " the pure frame structure with special - shaped columns ", " the frame - truss structure with special - shaped columns " and " frame - shear wall structure with special - shaped columns ", earthquake action analysis was done by the spacial finite element method through the changes structural parameter. analyzing systematically " structure vibration mode ", " vibration period ", " structure lateral rigidity ", " seismic action force ", " seismic response force ", " floor seismic shear force ", " lateral horizontal displacement of structure " and " members internal force ". results indicate : ( 1 ) based on equal area, the special - shaped columns replaced the rectangle columns, the structural lateral rigidity enlarges, the lateral displacement minishes obviously, the earthquake response increase slightly, the biggest increasing amount of frame columns axis - compress ratio is smaller than 0. 08. the whole aseismic performance of structure has improved ; ( 2 ) when the section ' s length and section ' s thickness ratio of special - shaped columns is smaller than 3. 6, the structure benefits to resist seismic action ; ( 3 ) the angle of horizontal seismic action with the whole coordinate is 0 degree, structure earthquake response is bigger, belonging to a control factor of structure aseismic design ; ( 4 ) the frame - truss structure with special - shaped columns and the " a " - brace has the biggest lateral rigidity ; ( 5 ) the frame - shear wall structure with special - shaped columns have bigger lateral rigidity and smaller displacement, members internal force enlarged just rightly, have much superiority of resisting seismic action ; ( 6 ) in the higher seismic fortification criterion region ( 8 degree of seismic fortification intensity ), aseismic disadvantageous building site ( iii type site ), adopting special - shaped columns structure system, should reduce possibly the building ' s self - weight in order to reduce the earthquake response ; ( 7 ) the response spectrum method of computing seismic response and the time - history analysis method have similar analysis result

    西安理工大學碩士學位論文在水平地震作用下，並考慮風荷載組合，分別對「矩形柱純框架結構」 、 「異型柱純框架結構」 、 「異型柱框一析架結構」及「異型柱框-剪結構」等四種結構體系，通過改變結構參數，運用空間有限元方法，進行地震作用計算。系統地分析研究「結構振型」 、 「振動周期」 、 「結構側向剛度」 、 「結構地震反應力」 、 「樓層地震剪力」 、 「結構側向位移」 、 「層間位移角」 ，以及「構件內力」 。結果表明:在等面積原則下，異型柱代換矩形柱后，結構剛度增大，側向位移明顯減小，地震反應力略有增加，框架柱軸壓比最大增幅小於8 % ，結構整體抗震性能有所提高;當異型柱肢長肢厚比小於等於3 . 6時，結構有利於抗震;水平地震作用力與整體坐標夾角為0度時，結構地震作用效應較大，屬結構設計的控制因素之一;異型柱框一析架結構採用「人」字斜撐，側向剛度大於「八」字斜撐和「人一八」字混合斜撐;異型柱框一剪結構側向剛度大、位移小，構件內力增大適中，是一種抗震性能優越的結構體系:在抗震設防烈度較高地區（ 8度）和抗震不利的建築場地（ m類場地） ，採用異型柱結構體系時，應盡可能減輕結構自重，降低地震作用力;分別採用「振型分解反應譜」法和「時程分析」法進行地震作用計算，兩種方法所得結果基本一致。
  5. Steel frame with welding joint easily occur brittle collapse because of having a low ductility at joints then ， a semi - rigid connected steel frame has large the energy absorption capacity which can resist dynamic loads and the using steel qualities of bracing system and joints are small so adopting a semi - rigid jointed steel frame is economical and stable but for semi - rigid connections are complex and variable ， in conventional analysis and design of steel structures ， it is usually assumed that the connections between columns and beams are either rigid or pinned the analysis of steel frames adopting the assumption can simplify the procedure of analysis and design ， but cannot precisely reflect structural practical circumstance and the errors of calculating results are large ， even ， get incorrect conclusions semi - rigid connection was referred to in chinese code for design of steel structures ( 2001 ， 10 ) ， however ， it isn ’ t specified how to apply semi - rigid joints in design in fact it cannot be carry out the purpose of the paper give a calculating method that accords practical engineering and easily put into effect worthwhile it is going to promote the development of semi - rigid jointed steel frame in design and heighten structural stability in the paper ， at first some commonly employed methods for the modeling of connection behavior are introduced richard abbott function modeling of connection is adopted for extended end plate bolted connection by the 34 test data comparing to regression analysis indicate richard - abbott function modeling of connection represents an excellent fit to test data then after a semi - rigid joint behavior can be modeled as a finite stiffness rotation spring ， base on rotation and displacement equation derive the element stiffness matrixes with semi - rigid connections where the effects ofj ointed flexibility geometric non - linearity and shear forces in the connection deformations have been considered in and fixed - end forces are modified finally, a program for calculating semi - rigid with incremental - iterative method has been

    本文的目的就是為半剛性連接鋼框架的設計提供一種既符合工程實際又簡便易行的計算方法，供規范使用過程的補充、延伸或參考；同時，也將促進半剛性連接鋼框架設計技術的發展，為提高結構安全性能、節省工程成本發揮應有的作用。本文首先介紹了常見的幾種應用較為廣泛的樑柱連接彎矩轉角關系模型，在分析比較的基礎上，選用richard ? abbott函數模型作為外伸端板連接彎矩轉角關系模型，通過對34個外伸端板連接的實驗數據與回歸分析得到的參數比較可知，經回歸分析得到的此模型參數與實驗數據符合較好。然後用彈簧表徵連接點的轉動剛度，根據梁的轉角位移方程推導出半剛性連接的剛度矩陣，在單元剛度矩陣中考慮了節點柔性、幾何非線性和剪切變形的影響，並對固端力進行了修正，最後用增量迭代法編制有限元程序進行計算和分析。
  6. C ompared the results of structural period, displacement and internal forces of mode 1 with mode 3, we can know that the hypo - frame can increase the lateral stiffness of the mega steel - frame structures, decrease lateral - deformation of the structures, especially decrease the maximum inter - storey displacement obviously, and get the internal forces and deformation of the whole structure more uniform. from the analysis results, it can be found that the maximum axial force gets less with hypo - frame than without it, and the maximum shear force and bending moment get more with hypo - frame than without it. thus it can be seen that the mainframe can be an independent structure system by itself, but the cooperation of main and hypo frame should be considered for conducting the entire analysis and design, otherwise the mega structure can be unsafe, in addition, from the comparing analysis, it can be found that the shear force and bending moment of inside - row columns are increased much more than those of outside - row ones in a mega column

    通過3個算例方案1和方案3結構周期、位移和內力反應的比較分析可知，次框架可以進一步增加巨型鋼框架結構的抗側剛度，減少結構側向變形，特別是明顯減少了結構最大層間位移，使整個結構的內力與變形分佈更為均勻；次框架的加入使主框架柱最大軸力較無次框架情況減少，而主框架柱的最大剪力和彎矩較無次框架情況都有所增加，由此可知，雖然主框架本身可以成為獨立的結構體系，但在分析設計時，還應該考慮主、次框架協同工作，進行整體分析、整體設計，否則結構會偏於不安全。
  7. Structural adhesives. determination of shear strength bonds axis - rings system

    結構粘合劑.環-軸粘接剪切強度的測定
分享友人
分享到 Line

分享到臉書