sintering phenomenon 中文意思是什麼

sintering phenomenon 解釋
燒結現象
  • phenomenon : n. 1. （pl. -na ） 【哲學】現象 （opp. noumenon）; 事件。2. （pl. phenomenons） 稀有現象；奇跡；珍奇；珍品；非凡的人。3. 【醫學】癥候。
  1. The simulation results suggest that, at the end of the scanning line, the dissymmetric temperature field and the great temperature gradient result in the balling phenomenon and great thermal stress, which could lead to the destruction of the sintering samples in this region. because of the coupling effect between scanning lines, the balling phenomenon is increased as the increase of the scanning lines, thus the over short scanning lines should be avoided in the sintering process. different scanning strategies have significant influence on the sintering

    模擬結果表明，掃描端點溫度場的不對稱及較大的溫度梯度造成了端點球化現象，並在端點處產生較大的熱應力，使燒結成形試樣易在此處破壞;激光掃描線間的耦合作用使端點球化現象隨掃描線的增加而逐漸顯著，燒結時應避免過短的掃描線;不同掃描策略對燒結成形有很大影響，交替掃描會影響燒結試樣的質量，實際製造時應採用單向掃描策略。
  2. Sicp / al matrix composites, with 5, 15 and 25 % volume fraction of sic particles, were prepared by vacuum hot - pressing sintering processing in this paper. based on mechanics properties, sem observation and energy dispersive x - ray analysis, the interface reaction phenomenon of sicp / al composites made by vacuum hot - pressing sintering, as well as the reinforcement and fracture mechanisms of this composite were analyzed. the dynamic responses of sipc / al composites were studied by a split hopkinson high - speed pressure bar impact system which strain rate was from quasistatic state strain rate ( 3. 3 10 - 3s - 1 ) to dynamic state strain rate ( 5. 2 103 s - 1 )

    本研究以武裝直升飛機防護裝甲材料為研究對象，採用真空熱壓粉末冶金燒結工藝制備了含sic顆粒體積分數分別為5 、 15和25的sic顆粒增強鋁基復合材料，結合其力學性能、掃描電鏡和界面微區能譜分析結果，分析了sic _ p al復合材料的真空燒結過程中的界面現象，以及材料增強和斷裂機理，並利用hopkinson高速壓桿沖擊實驗系統對其從靜態到動態（應變率為3 . 3 10 ~ （ - 3 ） s ~ （ - 1 ） 5 . 2 10 ~ 3s ~ （ - 1 ） ）的壓縮破壞響應進行了研究，分析了不同體積分數sic _ p al復合材料高應變率壓縮載荷下，材料的變形和微觀損傷機理，以及利用高速沖擊空氣炮測定了改復合材料制備剃度復合板的穿透性能。
  3. The dielectric constants of silica - rich, alumina - rich, and stoichiometric mullite ceramics are 5. 5, 6. 0 and 6. 3 respectively. the dielectric constant of mullite - si / c / n composites is related with the sintering parameters. with the increase of the sintering temperature and dwelling time, the " " and tg of mullite - si / c / n composites are decreased, this phenomenon is related with the change of the microstructure and phase composition of nano si / c / n powders

    莫來石- si c n復合材料的介電常數與熱壓燒結工藝有很大的關系，隨熱壓燒結溫度（ 1450 1600之間）的升高，燒結時間（燒結溫度為1550 ）的增長，莫來石- si c n復合材料的介電常數實部、虛部及介電損耗角正切均明顯下降，這與吸收劑的性質隨溫度和時間的變化有關。
分享友人
分享到 Line

分享到臉書