sleeve valve 中文意思是什麼

sleeve valve 解釋
【機械工程】套閥。

  • sleeve : n. 1. 袖子，袖套。2. 【機械工程】套筒，套管，套。3. 唱片套。4. 【氣象學】風（向）袋。vt. 給…裝袖子，給…裝套筒。adj. -less
  • valve : n 1 【機械工程】閥，活門，舌門；汽門。2 【解剖學；動物學】瓣，瓣膜；（貝）殼瓣；【植物；植物學】...
  1. Sleeve valve pipe grouting reinforcement for foundation of established building

    築物地基袖閥管注漿加固技術
  2. Application of sleeve valve barrel grouting in construction in domestic foundation engineering

    袖閥管注漿工法在國內工程施工中的應用
  3. Application of compound foundational underpinning for raft plank foundation with sleeve valve tube grouting in underground construction

    筏板基礎結合袖閥管注漿復合地基綜合托換法在地鐵施工中的應用
  4. Technical features, main requirements and process flow of sleeve valve barrel grouting method are described with the field cases of the method in grouting injection reinforcement, permeability proof and leakage treatment in china

    介紹了袖閥管注漿工法的特點、主要技術要求和施工工藝流程，以及該方法在國內注漿加固、防滲、堵漏施工中的應用實例。
  5. Abstract : technical features, main requirements and process flow of sleeve valve barrel grouting method are described with the field cases of the method in grouting injection reinforcement, permeability proof and leakage treatment in china

    文摘:介紹了袖閥管注漿工法的特點、主要技術要求和施工工藝流程，以及該方法在國內注漿加固、防滲、堵漏施工中的應用實例。
  6. Carefully remove the handwheel and turn indicator sleeve assembly, leaving the valve at its balance set point

    小心拆卸手輪，並旋轉指示器套筒總成，將閥門保留在它的平衡設置點上。
  7. Remove handwheel and turn indicator sleeve by grasping the handwheel and pulling away from the valve body along the stem

    拆卸手輪，並通過抓住手輪旋轉指示器套筒，將其沿著閥桿從閥體內拉出。
  8. With the handwheel / turn indicator sleeve assembly still at its balance set point indication, reinstall them on the valve stem and hold in place with the 1 / 4 " retaining bolt

    這時手輪/旋轉指示器套筒總成仍然位於平衡設置指示點上，將它們重新安裝到閥桿上，並用1 / 4英寸固定螺栓固定在其位置上。
  9. The valve stem with its grooved rings and positioning sleeve indicates the throttled position of the valve

    閥桿及其溝槽環和定位套筒顯示閥門的節流位置。
  10. In this paper the technolqical principle, furnish and application status of permanent mould with sand facing was introduced. application shows that the technology was suitable for mass production of high quality casting, suchas crankshaft ， valve and cylinder sleeve

    介紹了鐵型覆砂鑄造的工藝原理、工裝及生產應用情況，應用表明：該工藝適用於曲軸、閥體、缸套等大批量、高質量的鑄件生產。
  11. The reduced pressure detector assembly shall consist of two independent torsion spring check modules, a differential pressure relief valve located between and below the two modules, two drip tight shutoff valves, and required torsion spring check modules and relief valve shall be contained within a sleeve accessible single housing constructed from 304 ( sch 40 ) stainless steel pipe with groove end connections

    這種減壓檢測器總成應該包括兩個獨立扭力彈簧止回閥模塊，一個位於兩個模塊之間的下方的差壓安全閥，兩個防滴漏關閉閥，並且要求扭力彈簧止回模塊和安全閥應該放置在一個套筒內，要易於接近帶溝槽連接的304 （目錄40 ）不銹鋼管的單個外殼。
  12. Da traders specializes in accessory, battery, bolt and nut, brake shoe, cable camshaft, clutch and parts, c v joint, cylinders, fastener, fuel system, horn, ignition coil, lamp, mirror, motorcycle parts, oil seal, piston / ring / pin, relay, shock oxygen, shock absorber, sleeve, spark plug, starter, valve / guide / seat, wheel hub bearing / unit

    該貿易公司主營螺栓和螺母，火花塞，輪轂軸承，附件，電池，剎車蹄，線束，凸輪軸，離合器，萬向節，喇叭，點火線圈，車燈，車鏡，摩托車配件，油封，活塞，活塞環，繼電器，減震器， ，起動器，氣門座圈，氣門導管。
  13. Note : the valve is shipped in the closed position. the indicator on the plastic sleeve is aligned with the vertical scribed line on the stem

    注意：閥門裝運時是處于關閉位置。塑料套筒上的指示器與閥桿上的垂直刻線對齊。
  14. Also, provide a protective sleeve that allows operation of the valve without breaking the vapor seal or disturbing the insulation

    此外，還要配置保護性套管，使得時不會破壞氣體密封或絕緣性能。
  15. Safety valve pressing sleeve

    安全閥壓套
分享友人
分享到 Line

分享到臉書