speed of flooding 中文意思是什麼
speed of flooding
解釋
泛水速度-
In the study of the lumber carrier, one of the very important problem is the in spot and ultimate station due to flooding which will bring tremendous threat to the ship because of the few holds in order to study the lumber carrier buoyancy, stability and longitudinal strength under the condition of flooding, the paper adopt fundamental ship principle and iterative and accumulative concept on the basis of insumersibility theory to detailedly calculate the flooding speed flooding amount front draft after draft stability and longitudinal strength considering the ship " s sinking and inclination which will change the center of gravity and the loading station both in hold and on deck and the effect of flooding and lumber amount in holdo in the last, the paper introduces an example of the actual ship named " fei yun ling " and makes a contrast between not taking measure and taking measure which draws a reasonable conclusion and comes up to some advice the method avoids the cockamamie calculating while insures enough precision the paper draws a conclusion that not all the lumber carrier will submerge when suffering the damaged flooding if the loading or measure is suitable
為了研究運木船舶在破艙狀態下的浮性、穩性和強度，本文在抗沉性理論的基礎上，運用船舶基本原理，採用了迭代和累計的思想，將船舶的進水過程劃分為很多次進水的積累，詳細計算了運木船在破艙進水的過程中，考慮到各種破艙參數、船舶本身的下沉、艙室內木材、甲板貨的裝載情況和在進水過程中船舶本身的傾斜對進水重心的影響，以及艙室內的進水量和木材對破口處進水速度的影響，船舶總的進水速度、進水量、首尾吃水、穩性的實時狀態和最終船舶的總縱強度，給出了計算實例，並進行了在採取用泵抽水前後浮態參數的對比，得出了該船舶在艙室內的貨物積載量達到某個數值時可以保證船舶在破艙進水時不會沉沒，或者在當開口小於某數值時，採取適當的措施后，可以使船舶避免沉沒。 -
It shows that the injection quantity and the difference of temperature distribute as a parabola which is at the same load, and the minimum of the parabola corresponds to the optimum quantity of injection ( g ). under the condition that the quantity of injected mass, the air speed and the heat quantity is respectively g, v and q, the research demonstrates that the pentium iv chip ' s temperature variation can be controlled under 40c and work normally when the wind speed overpass 1. 5m / s and the power dissipation of the chip is 60w. otherwise this paper calculates the flooding limit of thermosiphon with several different methods
對其充灌量、散熱量、電子元件（ cpu模擬晶元）表面與環境溫度之差及通風、流速的影響進行了系統的測試，發現充液量與溫差的關系在負荷不變時呈拋物線分佈，其極小值點對應的充液量是最佳充液量g 。在充液量為g時，對風速v 、散熱量q進行的研究表明，當風速超過1 . 5m / s后，奔騰晶元在60w發熱條件下晶元溫度小於40 ，能滿足長期正常工作。 -
After analyzing, the author got the basic character of tidal flat hydrodynamic : the time of flooding on bare flat and ebbing is basically the same and the time of flooding on pioneer zone of salt marsh is a little short ; the process curve of current speed on bare flat did not appear peak value on the beginning of flooding and at the end of ebbing but presented double peak, that is, it presented double peak in winter and spring and ebbing peak value disappeared in summer and autumn, salt marsh presented single peak character in a year and the process curve in tidal creek presented double peak ; all current direction on every spot presented gyration current and the current speed changed rapidly during the high water level without obvious slack water period
分析得到了潮灘水動力基本特徵：光灘水位漲潮和落潮時間基本相等，而鹽沼前緣帶水位漲潮時間略短；光灘流速過程線在漲潮初和落潮末出現峰值，呈現「雙峰型」特徵，鹽沼前緣帶則冬、春季節呈現「雙峰型」 ，夏、秋季節落潮峰值消失，鹽沼帶四季呈現單峰特徵，潮溝內過程線為「雙峰型」 ；各測點流向均呈現回轉流特徵，在高水位時流向迅速改變，不存在明顯的憩流。
分享友人