spray-droplet 中文意思是什麼
spray-droplet
解釋
噴射油滴-
As to the simulation, three - dimensional n - s equations and two - phase flow model, in which the liquid toluene spray as discrete particles was considered, were employed to describe the turbulent combustion processes in the combustion chamber. the mass and energy transfer between the two phases were calculated by the droplet evaporation model, and the arrehnius model was used to obtain the gas chemical reaction rate. the details of 3d flow field, the distributions of temperature and compounds were obtained by solving the equations
數值模擬方面，應用三維湍流n - s方程以及顆粒軌道模型描述了激光器燃燒室內部的噴霧兩相燃燒流動過程，兩相之間的質量、能量交換由液滴蒸發模型計算，氣相化學反應速率由arrhnius公式計算，通過耦合求解氣液兩相模型方程，模擬了燃燒室三維流場，得到了燃燒室內的溫度和組分濃度分佈。 -
Using entropy theory, the droplet distribution of diesel spray is predicted in this paper as well
運用最大熵原理，對柴油在不同噴油條件下的粒度分佈做了預測。 -
The basic principle of charged droplet ' s fission and electro - spray with different charging method are presented
分析了霧滴帶電破裂和採用不同充電方法進行荷電噴霧的基本原理。 -
Aimed at some problems such as short spraying distance, electricity - leaking and reverse ionization among electrostatic nozzles existing in the country, a induction charging and pneumatic energy electrostatic nozzle was designed. the basic designing theories, structure and working process of this nozzles were theoretically specified in the paper. and then the atomization quality and charge performances of this nozzle and its affecting factors were studied by carrying out performance experiment and statistic analysis. result of the studies indicate : ( 1 ) some progress were made in solving the problems list above ; ( 2 ) from this nozzle, droplet were minute and uniform, and higher charge - mass ratio can be obtained under lower electrostatic voltage, thus the atomization quality and charge performance of this nozzle were both better ; ( 3 ) within the experiment extend, air pressure at 0. 2mpa, electrostatic voltage at 2400v were the most suitable parameters for the nozzle ; ( 4 ) the regression equations for describing droplet size, intensity of spray current and charge - mass ratio of this nozzle obtained from the experiment data had higher forecast precision ; ( 5 ) cross - effect of all factors were not significant, the atomization quality and charge performance were relative dependency affected by the factors
諸試驗因素中，充電電壓和噴孔直徑對霧滴荷質比均有極顯著的影響；氣體壓力和液體流量對霧滴荷質比的影響均不顯著；影響霧滴荷質比的主要因素依次為充電電壓和噴孔直徑; （ 8 ）在300v 、 600v 、 1200y 、 1800y 、 2400v 、 3000v六種充電電壓t ，霧滴荷質比先隨充電電壓的增加而增大， 2400v后荷質比減小，推測:對于所研製的噴頭可能存在一個最佳充電電壓; （ 9 ）由充電電壓和噴孔直徑的不同搭配所得霧滴荷質比不同這一結果，可看出，較大充電電壓需配備較大噴孔直徑以增強霧滴荷電效果; （ 10 ） td3 . 6和td3 . 4兩噴頭的霧滴荷質比曲線趨于重合，說明噴孔直徑大於滬3 -
This paper reports the droplet size and distribution, penetration and diffusionangle of fuel spray before and after impingement by multiple - picture overlapping photography and laser technology, as well as the fuel spray mixing and burning process in a direct injection diesel engine by high speed photography
本文介紹了用多次噴霧疊加攝影與激光粒子分析技術對燃油噴霧撞擊前後的粒徑、貫穿度以及噴霧錐角等因素變化所進行的觀察和測量以及介紹了利用雙像高速攝影技術對燃油束撞擊霧化形成的混合氣以及燃燒過程特點的研究。 -
The reagent slurry is injected through rotary atomizers or dual - fluid nozzles to create a finer droplet spray than wet scrubber systems
試劑泥漿通過轉臺式霧化器或雙重流體噴管進行噴射，形成比濕式凈化器系統更優良的滴狀噴霧。 -
The results turned out that the crystal structure was changed by the variation of the deposition temperature and annealing time. the surface morphology was greatly influenced by the spray parameters which atomized the precursor droplet in different diameters and different intensities
薄膜的表面形貌隨著噴霧參數的改變發生了較大的改變，噴霧參數的改變使是霧化液滴大小和液流密度隨之發生了一定改變。
分享友人