starting velocity 中文意思是什麼
starting velocity
解釋
初速-
In view of this situation this article has conducted research to the design of metallurgy auxiliary biography with the frequency conversion table electrical machinery first multianalysis to the frequency changer and the frequency conversion table electrical machinery movement characteristic is carried out, the voltage waveform harmonious which the frequency changer outputs is big, attacks in a big way, and the voltage climbing rate reaches as high as 6600v / mu s which is 20 times ordinary sine alternating voltage, the rolling mill auxiliary biography table set the extremely strict request to the electrical machinery ; its movement frequency is very low, rate frequency in 8 - 20hz ; the velocity modulation scope is wide, the lowest movement frequency lowers to 1hz, and the starting number of times is quite frequently, each hour reaches as high as 600 - 800 time, the impact shoulders in a big way, the overload capacity request is high
針對這一情況本文對冶金輔傳用變頻輥道電機的設計進行了系統研究。首先對變頻器和變頻輥道電機的運行特性進行詳細分析，變頻器輸出的電壓波形諧波大，沖擊大，電壓上升率高達6600v / s ，是普通正弦交流電壓的20倍;軋機輔傳輥道對電機提出了十分嚴格的要求:其運行頻率很低，額定頻率在8 - 20hz ;調速范圍寬，最低運行頻率低到0 . 5hz ，起動次數相當頻繁，每小時高達600 - 800次，沖擊負荷大，過載能力要求較高。 -
This article angle has analyzed the higher professional technical education from cbe / dacum " the electrical control technology " the curriculum ability localization, according to the higher professional technical education " the electrical control technology " the curriculum ability localization, point out the insufficiency and flaw existed in commonly used control electric appliance choice, electrical pilot wire road map, electricity control system installment, wiring craft, electrical control line fault diagnosis system approach, new starting velocity modulation equipment and control circuit, control circuit and main circuit aspect and so on
摘要本文從cbe / dacum角度分析了高職「電氣控制技術」課程的能力定位，根據高職「電氣控制技術」課程的能力定位，指出了現行高職「電氣控制技術」教材在常用控制電器選擇、電氣控制線路圖、電氣控制系統安裝、接線工藝、電氣控制線路故障診斷的系統方法、新型起動調速設備及控制電路、控制電路與主電路的連接等方面存在的不足和缺陷。 -
The programme logic controller is utilized to control the inverter ' s output frequency which accomplishes controlling the velocity of speed - controlling asynchronous moter. the velocity between main asynchronous moter and speed - controlling asynchronous moter is composed by way of the differential planetary gear train, the tranmission system is made to regulate velocity stepless in large scope which succeed in controlling starting progress of load
使用可編程式控制制器對變頻器的輸出頻率進行控制，實現對調速電機轉速的控制。調速電機與主電機的轉速經差動行星輪系的速度合成，可使傳動系統在很大范圍內無級調速，實現對負載的可控起動。 -
The simulated test of the mechatronics soft start equipment is made regarding the experimental platform of belt conveyor as load, the sensor design is had for selecting type, the testing datum are gatherd and analyzed, the rational curve of velocity in the starting and braking progress are gained, the best matching ratio of driving power for the double asynchronous moters is found
以帶式輸送機實驗臺為負載進行了機械電子式軟起動裝置的模擬試驗，對傳感器進行了選型設計，對試驗數據進行了採集與分析，確定了合理的起、制動速度曲線，求出雙電機驅動功率的最佳配比。 -
And the relation between these velocity was analyzed at last. this is the conclusion : ( 1 ) the distribution of the velocity and concentration are get in the open channel flow and as the sewage flow is gravity flow, the equations is fit for this too. ( 2 ) generally speaking, the self - cleaning velocity should be the starting velocity, and it could fit for the self - cleaning target in limited sense theoretically, but when facing some higher requirement, it is not large enough
最後結合污水流動的最小設計流速與顆粒起動流速、臨界不淤流速的關系進行了分析，結論如下: （ 1 ）文中所得出的速度分佈與濃度分佈是在明渠兩相流動情況下推得的，由於污水管道流動多為重力流，是明渠流中的一種，所以文中的分析在認識污水流動特性方面具有一定的參考價值。 -
According to the practical geological model of slope, by means of the finite element analysis, from the constitutive equations of the elastoplasticity and the viscoelasticity - viscoplasticity, the process and mechanism for progressive failure of the locked segment of rockmass are quantitatively revealed and simulated during the rupture, deformation, destruction, and failure of highsteep slope rockmass, and the dynamics driving the motion of rocky landslide with violent starting velocity by high pressure water flow is dealed with
根據邊坡實際地質模型，基於彈塑性與粘彈-粘塑性理論的本構方程，通過有限元模擬分析，定量地揭示和模擬再現了高邊坡巖體破裂、變形、破壞及失穩前後鎖固段巖體漸進性破壞的機制和過程，探討了高壓水流作用下滑坡啟程劇動的破壞機理。 -
( 2 ) starting off with analyzing the forces affected on single dry solid granule on the roller screen, the relative slippage and slipping condition of granule at the tangential direction and axis direction of roller screen are discussed, and the average slipping conveyance velocity from feeding end to discharging end is given. the throwing conveyance of granule is discussed, the throwing coefficient of roller screen and its varying rule, and the concept of average throwing coefficient and its computing method are put forward, the starting condition and terminating condition for throwing motion of granule on the roller screen and the throwing conveyance velocity of granule are researched. the influence on throwing motion of granule by the rotating velocity of roller screen is discussed as well
（ 2 ）從筒式篩網上單顆干固相顆粒的受力分析著手，討論了顆粒在筒式篩網面上的切向相對滑動和軸向相對滑動及滑動條件，並導出了顆粒從進料端向出料端滑動運移平均速度；討論了顆粒的拋擲運移，給出了筒式篩網上的拋擲指數及其變化規律，提出了筒式篩網的平均拋擲指數的概念及計算方法，研究了筒式篩網上顆粒拋擲運移的產生條件和終止條件，以及顆粒拋擲運移的輸送速度；還討論了筒式篩網的旋轉角速度對顆粒拋擲運動產生的影響。 -
The transmission method and control theory of the hydraulic traveling system of the paving machine are described in detail in the paper. the paper puts out a specific control strategy to control the machine ' s running forwards and backwards, starting, braking, accelerating and decelerating, and or so, turning right and left and steering, at the same time, puts great emphasis on the study of constant - velocity technology and integrates the pid theory and fuzzy control theory into the design of the digital controller
詳細論述了瀝青混凝土攤鋪機液壓行駛系統驅動方式和控制原理，提出了具體的控制方案，用單片機完成了攤鋪機行駛系統數字控制器的硬體設計和軟體設計，實現了攤鋪機前進後退、起步、停車的加速與減速控制，以及左右轉向和原地轉向的控制。 -
Starting wind velocity
起動風速 -
It not only controls the machine " s running forwards and backwards starting, braking turning right and left, and so on, but also puts great emphasis on the study of constant - velocity control
在實現攤鋪機的前進後退、停車、起步、左右轉向及原地轉向等基本功能的基礎上，重點討論了攤鋪機工作在攤鋪狀態下的恆速控制問題。
分享友人