steam flow rate 中文意思是什麼

steam flow rate 解釋
蒸氣流量
  • steam : n 1 蒸汽，水蒸氣，水氣，霧，蒸氣壓力。2 〈口語〉精神，精力，氣力；怒氣。3 輪船，乘輪船旅行。vi 1 ...
  • flow : vi 1 流，流動。2 （血液等）流通，循環。3 流過；川流不息；（時間）飛逝；（言語等）流暢。4 （衣服、...
  • rate : n 1 比率，率；速度，進度；程度；（鐘的快慢）差率。2 價格；行市，行情；估價，評價；費，費用，運費...
  1. The goal is to control the water outlet temperature by manipulating the flow rate of the steam and control the water inlet rate by manipulating the height of the water level in the water tank

    本文中，換熱器的控制任務主要有兩個，首先通過控制水箱進口水閥門開度，進而控制水箱水位，進而控制換熱器進口水流量。
  2. Through analyzing the effect of temperature and nitrogen on crude oil viscosity the influences of different nitrogen injection volume and injection modes on steam displacement are contrasted, the mechanism of nitrogen - assisted steam stimulation is clarified, which includes : heat carrying capacity is raised, the saturation of remaining oil is reduced after nitrogen - assisted injection is made ; crude oil flow is enhanced because of nitrogen compression and dispersion and the change of oil flow shape ; water back - production rate is improved by expanding the steam sweep volume and compensating in - situ energy ; steam distillation effect is enhanced

    通過分析溫度、氮氣對原油粘度的影響，對比不同注氮量、不同注入方式等對蒸汽驅油效果的影響，弄清了氮氣輔助蒸汽增產的機理主要表現在：氮氣輔助后增加攜熱能力，降低殘余油飽和度，氮氣的壓縮膨脹作用分散和改變了原油流動形態，增強了原油流動性；擴大蒸汽的波及體積，補充地層能量，提高回採水率，強化蒸汽蒸餾效應。
  3. In this paper, through the cfd modeling of the ash - agglomerated fluidized bed gasifier, the gas molar concentration distributions in the bed with the influences of the oxygen flow rate from the central nozzle, the steam flow rate from the distributor and the pressure of the bed are studied

    摘要通過cfd模擬了灰熔聚流化床氣化爐，考察了操作條件包括中心管氧氣量、分佈板水蒸氣量以及操作壓力對流化床氣化爐的氣相濃度分佈的影響。
  4. Concentric jacket pipe surrounded the test condenser. steam was generated in the boiler, flowed upward to the inlet of connection pipes, then flowed downward into the condenser tube, the cooling water flowed countercurrently through the annulus. the experiment covered the range of the pressure 1. 0 ~ 3. 0bar, heating power 2. 0 ~ 15. 0kw, steam mass flow rate 0. 001 ~ 0. 004kg / s, air mass flow rate 0. 0 ~ 0. 00163kg / s, and cooling water temperature 20 - 60 ?

    在系統壓力為0 . 1 0 . 3mpa ，加熱功率為2 15kw ，蒸汽質量流量為0 . 001 0 . 004kg s ，空氣質量流量為0 . 0 0 . 00163kg s ，二次側冷卻水溫度20 60的范圍內，系統研究了豎直下降管內含有空氣的蒸汽冷凝特性，獲得了不同壓力、不同空氣含量和不同加熱功率下，冷凝段的溫度分佈和局部熱流密度的數據。
  5. Measurements were made of system pressure, mass flow rate of steam, air, and cooling water, temperatures of condensing flow and cooling flow, and the water level of boiler. the major phenomena observed in the present experiment are similar to those by other investigators. the mass flow rate of steam, the system pressure and air content are the most important factors affecting steam condensation

    實驗結果表明，維持二次側冷卻水流量不變，無論對于純凈蒸汽還是含有空氣的蒸汽冷凝，隨著蒸汽發生器加熱功率的增大（即蒸汽流量增大） ，有效冷凝段長度將加長；當蒸汽中含有少量空氣，有效冷凝段長度也會明顯加長；提高系統壓力，有效冷凝段長度將縮短。
  6. The break was assumed to be a single tube double - ended and three - tube double - ended shear break. the diameter of the break orifice is 0. 876mm and 1. 518mm respectively. the characteristic responses of main thermal - hydraulic parameters, such as primary pressure, secondary pressure, break flow rate, pressurizer level, secondary side level of steam generator and so on, were presented in this thesis

    試驗再現了核電廠蒸汽發生器單根傳熱管雙端斷裂事故和三根傳熱管雙端斷裂事故發生后的熱工水力現象，給出了事故過程中一次系統壓力、二次系統壓力、破口流量、蒸汽發生器二次側水位、穩壓器水位、元件表面溫度等主要參數的瞬態響應。
  7. According to the coal rank, blending rate, combustibility and slagging ability, the optimization process flow sheet of steam coal blending are introduced briefly. total coal quality engineering analysis system is set up

    基於煤質工程分析來進行優化配煤，不僅考慮了煤質對鍋爐燃燒過程的影響，而且考慮煤質對整個鍋爐工作過程以及電廠工作過程的影響。
分享友人
分享到 Line

分享到臉書