stress cone 中文意思是什麼
stress cone
解釋
應力錐-
At first in the condition of low - velocity impact it is discussed with the formation of ceramic smash cone angle on the base of quasi - statistic hertz and 3 a 6 y a c - theory. then using spherical stress wave reflection and transmission theory under the state of medium - high velocity the formation of spot in the ceramic back. finally the damage mechanism of ceramic suffered by the high impact is simply discussed
首先，在低速撞擊的條件下，基於準靜態hertz的理論與薩布斯基理論，分析了陶瓷破碎錐角的形成；其次，在中高速撞擊條件下，利用球面應力波反射迭加理論，分析了陶瓷背面的層裂的形成；最後，簡單討論了高速撞擊下陶瓷的破碎機理。 -
Contact stress analysis on the bearing of single - cone bits
單牙輪鉆頭軸承接觸應力分析 -
A series of results are achieved such as fluid field thermal field pressure field and stress field. those results show that sphere target has better heat exchange and convenient fluid structure and that cone target is easy to accepting neutron and has the convergent stress. taking into account the thermal - hydraulic and physics discipline, solid target choose sphere structure but liquid target still should further consider of material study
計算結果表明：圓球靶型散熱快，流道設計方便;錐形靶易於接收中子，但結構易引起應力集中，在綜合熱工、物理兩個角度，固態靶選取圓球型鎢靶比較滿意，液態靶區的計算需要在材料研究的基礎上進行。 -
By comparing between the rectangular groove and curved groove, we find that two high stress area of rectangular groove o - ring occurs during the sealing period, and the wearing on the both inside and outside diameter surfaces ; the high stress area only happens at the part area of cone shaft, and the distribution of stress is more even than the former, and the wearing is on the inside diameter surface, the improvement of its distortions makes the service life of sealing lengthen
通過矩形槽和弧形槽的對比研究發現，矩形槽o形圈在密封過程中出現兩個高應力區，磨損發生在內徑、外徑兩個表面_匕，弧形槽o形圈的高應力區僅出現在牙爪軸鄰近的局部區域內，應力分佈較前者更為均勻，磨損進發生在內徑表面，其受力變形狀況的改善將使密封壽命進一步提高。 -
The opening stress and the life of crack growth is calculated and compared with the test results and the experience formula. the feasibility of the newman theory of opening stress used in the high strength steel is validated. then through the slice synthesis method, the three dimension surface crack of the weld joint of cone - cylinder is decomposed into many plane through cracks
本文將基於裂紋閉合現象建立的帶狀屈服模型，用在平面貫穿裂紋中，計算此時的裂紋張開應力和疲勞裂紋擴展壽命，與試驗結果和經驗公式比較，驗證newman裂紋張開應力理論在高強鋼中的可行性；然後，用切片合成法，把潛艇結構凸錐柱結合殼焊縫處的三維表面裂紋分解成平面貫穿裂紋，用帶狀屈服模型的理論來分析平面貫穿裂紋，得到裂紋沿深度方向的擴展速率，進而得到潛艇結構的疲勞壽命。 -
General rules were validated and a new rule was discovered : i. e. the shape 0f these two stress fields are same, the equivalent stress of the round corner in the bottom reached its maximum at the first phase, the equivalent stress of the edge of hole reached its maximum at the third phase, the equivalent stress of flanging with cone - shaped punch descend more than that with column - shaped punch at the fourth phase i. e. the phase of deformation completed
驗證了一般規律，也發現了新規律，即兩者的應力場形狀相同，底部圓角處等效應力在變形第1階段最大，孔口邊緣處等效應力最大出現在變形第3階段，第4階段（變形終了時）錐形沖頭翻邊的等效應力比柱形沖頭翻邊時下降更大。 -
05. 02 test method for yield stress of heterogeneous propellants by the cone penetration method
用針入度法測定非均質推進劑的屈服應力的試驗方法 -
The calculation results show that the stress distributing of the plug drawing tube is different because of different dies, the drawing force and pulling force are lager in arc die and the diameter and wall thickness are closer to the designing value in cone die
計算結果表明，不同的模具，芯拔管的應力分佈不同，弧形模成型的拔制力與芯棒后拉力較大，錐形模成型后鋼管的直徑與壁厚更接近設計值。 -
Standard test method for yield stress of heterogeneous propellants by cone penetration method
錐入度法測定多相推進劑屈服應力的標準試驗方法 -
Cone of shearing stress
切應力錐 -
Cone - based rheometer was modified to estimate the rheological properties of fresh mortar, which can measure yield stress and plastic viscosity of mortar in relative units. effects of many factors on rheological properties of mortar were studied. a set of test theory and method for designing rheological properties of mortar was recommended
用它研究了各種因素對砂漿流變性的影響；證實了砂漿的屈服應力與塑性粘度是互相獨立的物理量，屈服應力決定變形能力，塑性粘度決定變形速率；為砂漿流變性設計提供了一套測試理論和方法。 -
Through using abaqus software, a numerical simulation of equivalent stress field of flanging deformation process with cone - shaped punch was carried out, and compared with simulation of flanging deformation with column - shaped punch
摘要利用abaqus商用軟體，對錐形沖頭翻邊變形過程的等效應力場進行了數值模擬，並與柱形沖頭的翻邊變形模擬進行了對比。
分享友人