temperature-time combination 中文意思是什麼

temperature-time combination 解釋
溫度時間關系
  • temperature : n. 1. 溫度，氣溫。2. 體溫。3. 〈口語〉發燒，高燒。
  • time : n 1 時，時間，時日，歲月。2 時候，時刻；期間；時節，季節；〈常pl 〉時期，年代，時代； 〈the time ...
  • combination : n 1 結合，合併，混合，聯合，配合，組合。2 合作；共謀，同謀；同黨。3 〈pl 〉〈英國〉連褲襯衣。4 【...
  1. So only with the best combination of dispersants concentration, dispersing time, ph, temperature and adscititious ions, steady dispersing system can be obtained

    只有在分散劑濃度、分散時間、 ph值、溫度和外加離子濃度的最佳組合條件下，才能得到穩定的分散體系。
  2. The sensitivity algorithm is a knowledge of research on the affection of parameters varies to system performance. combination with pressing force and infuse time predicted model, by using sensitivity algorithm, the affection of cast temperature, mould temperature and infuse pressure on infuse time is researched deeply, and the affection of cast temperature, infuse time and infuse pressure on the pressing force in the origination stage of extrusion process. the sensitivity analysis has huge instructing significance to the selection of parameters

    靈敏度演算法是分析參數變化對系統性能影響的一種有效工具，所以本文引入靈敏度演算法，結合壓制力和浸滲時間預測模型，深入研究了澆注溫度、模具溫度和浸滲壓力對浸滲時間的影響關系，以及澆注溫度、模具溫度、浸滲時間和浸滲壓力對擠壓過程起始階段壓制力的影響，對于參數的選取，具有一定的指導意義。
  3. Secondly, during the braising offline temperature control loop of the oil production - lixiviating procedure, the controlled object, which is hard to build the extract model, has the characteristics of large inertial, big time - delay. the control strategy of the combination of fuzzy logic arithmetic and normal pid arithmetic is introduced in this paper, the basic principle and actualization method of fuzzy - pid are analyzed. the design model is simulated in matlab and the result proves good control performance

    其次，玉米油生產浸出工序的蒸脫機溫度控制迴路中，被控對象具有難以建立精確的數學模型，且具有大慣性、大滯后的特點，研究運用模糊控制演算法和經典pid控制演算法相結合的控制策略，分析了模糊pid控制演算法的原理和實現方法，並運用matlab軟體對設計的系統進行模擬，模擬結果表明，達到較好的控制指標。
  4. We use time domain reflectometry ( tdr ) to simultaneously estimate volumetric soil water content, soil solution electrical conductivity, and soil nitrate concentrations in combination with porous ceramic cup solution samplers to follow no3 - n transport in soil exposed to different irrigation, fertilizer quota and temperature. the experiment was conducted with nondestructive soil colums

    本研究中以原狀土為研究對象，利用時域反射技術隨時測定土壤含水量和電導率的特點結合多孔陶瓷杯抽濾技術，研究在不同灌水、施肥和溫度下硝態氮的變化。
  5. It has shown that the combination with higher magnetic and mechanic properties of the bonded magnet is presented on the basis of proper curing process temperature, 120 cto 150 c, and the curing agent is and proper mold press, 500 - 600mpa, keeping press time is 20 seconds

    固化工藝中的固化溫度不宜過低，應以120到150之間為宜。在壓制過程中，模壓壓力為500 600mpa ，保壓時間為20秒時可以使粘結磁體的密度達到最高值，且具有較好的磁性能和力學性能。
分享友人
分享到 Line

分享到臉書