testing for failure 中文意思是什麼

testing for failure 解釋
負面測試
  • testing : 測試系統
  • for : FOR f o r ＝ free on rail 【商業】火車上交貨（價格）。1 〈表示目標、去向〉向，往。 leave [sail] f...
  • failure : n 1 失敗 （opp success）; 不及格。2 不足，缺乏；衰退；【醫學】衰竭。3 不履行，玩忽。4 破產，倒閉...
  1. Standard test method for adhesion strength and mechanical failure modes of ceramic coatings by quantitative single point scratch testing

    用定量單點劃痕試驗測定陶瓷塗層粘結強度和機械損壞類型的標準試驗方法
  2. Two new methods have been put forward to estimate the reliability characteristic parameter. a software package has been developed to process the data obtained from reliability testing for electric apparatus. it consists of both the determination of failure distribution and the estimation of reliability characteristic parameter

    最後，設計出電器可靠性試驗數據處理軟體包，此軟體包含了產品失效分佈類型的確定和可靠性試驗結果為大子樣、小子樣、無失效數據時可靠性特徵量的估計方法，以及恆定應力加速壽命試驗數據下的可靠性特徵量的估計方法。
  3. Equipment reliability testing - tests for the validity of a constant failure rate assumption

    恆定失效率假設的有效性檢驗
  4. For example, the weakness in metals etc. caused by repeated stress. this article gives the point estimation of parameters based on tampered failure rate model for weibull distribution under step - stress accelerated life testing

    本文是針對損傷失效率模型（ tfr ）模型就weibull分佈產品在步進應力加速壽命試驗下研究了參數的點估計。
  5. Equipment reliability testing - tests for the validity of the constant failure rate or constant failure intensity assumptions

    設備可靠性試驗.恆定失效率或恆定失效密度設想的有效性試驗
  6. Equipment reliability testing - part 6 : tests for the validity of the constant failure rate or constant failure intensity assumptions

    設備可靠性試驗.第6部分:恆定失效率和恆定失效強度先決條件下的有效性試驗
  7. Statistical analysis of weibull distribution for tampered failure rate model in progressive stress accelerated life testing

    分佈步加應力壽命試驗混合數據的統計分析
  8. Reliability testing - compliance tests for constant failure rate and constant failure intensity iec 61124 : 2006 ; german version en 61124 : 2006

    原油中鐵鎳鈉釩含量的測定原子吸收光譜法
  9. Single parameter provides little message and sometimes it is difficult to make an exact evaluate. in this paper, by testing the sensitivity of the system model, three parameters are selected as sensitive parameters, and based on simulation result of the system model, three dimension failure surface is used for alarm criterion and arithmetic of the alarm is carried out

    單一參數提供的信息較少，有時難以作出準確的評價，本文通過對系統模型的靈敏度測試，選取三個參數作為靈敏參數，根據系統模型的模擬結果，以三維失效面作為報警判據，並實現了報警演算法。
  10. This dissertation mainly introduces the research and development work of the hcq3. 0 testing system for automobile ' s rear - axle, which produced by xuzhou meritor axle co. ltd. it analyses the anti - fatigue failure ability of the rear - axle and the software development

    本論文對驅動橋的疲勞試驗技術研究和試驗臺系統軟體的開發進行了深入的分析，論文共分六章，各章內容如下：第一章、緒論簡要介紹了汽車檢測技術和驅動橋試驗臺的發展及其現狀，介紹了常見的驅動橋試驗臺類型。
  11. Train operators and maintenance technician for failure analysis and reparation of testing equipment

    培訓生產人員和維修人員如何進行測試設備缺陷分析和維修。
  12. Reliability testing - compliance tests for constant failure rate and constant failure intensity

    可靠性試驗.恆定故障率和恆定故障強度的審核試驗
  13. Equipment reliability testing - compliance test plans for failure rate and mean time between failures assuming constant failure rate

    設備可靠性試驗恆定失效率假設下的失效率與平均無故障時間的驗證試驗方案
  14. Equipment reliability testing - part 6 : tests for the validity of the constant failure rate or constant failure intensity assumptions iec 60605 - 6 : 1997

    設備的可靠性試驗.第6部分:對恆定故障率或恆定故障密
  15. In fact, the confirmation of the cause for such a specific failure could hardly be made with only limited data material from the preliminary investigation stage, and without a huge amount of testing

    實際上，如此具體的故障原因的確定，不經一定數量的試驗，僅憑查閱調查初期階段的一些資料，是不可能得出的。
分享友人
分享到 Line

分享到臉書