time displacement 中文意思是什麼

time displacement 解釋
時間平移
  • time : n 1 時，時間，時日，歲月。2 時候，時刻；期間；時節，季節；〈常pl 〉時期，年代，時代； 〈the time ...
  • displacement : n 1 轉位，移動；取代，置換；（人的）流離失所。2 撤換，免職。3 【機械工程】（活塞）排氣量；【航海...
  1. The existing theoretical analyses have n ' t refelcted this true mechanism of the force transfering in fixed segment of anchor bar. for the sake of studying the working course from elastic to elastoplasticity slide better, this paper put forward shear stress - displacement curve, and solve the internal force distribution along anchor bar by the basic equntion. at the same time, this paper analysize the difference of columniform fixed segment and the segmeng with anchor slab at the foot of anchor bar

    為了更好的研究錨桿在不同荷載作用下，錨桿的工作狀態從彈性到彈塑性發展的整個過程，本文進行了錨桿受力的模型實驗研究，根據實驗結果提出了剪應力與位移的彈塑性本構關系表達式，並根據錨桿受力的基本方程，求解得出了錨桿在不同工作狀態下從彈性到彈塑性滑移的全過程中錨桿的內力分佈。
  2. On this foundation the article inducts in detail the method which is based on the relative settlement of calculating unit area end support ( qb ) force at the same time considering the feature of pedestal pile ' s " arch effect " the article introduces conception of pile effective length and finally obtain t he formula of calculating man - made pipe with bulb - shaped axial carrying capacity. the article uses marc program to calculate and analyze foundation soil ' s stress and displacement and gets the change curve chart and the proportion that is shared by king - pipe side soil friction resistance and pipe end counterforce respectively. the article inducts the structure of pedestal in detail on the basis of generalizing pedestal application cases of many countries

    在此基礎上論文詳細歸納了以相對沉降為依據確定單位面積端承力q _ b的計算方法，並考慮擴底樁的「拱效應」特點引入了有效樁長的概念，最後結合公路規范推出了比較實用的人工挖孔擴底樁軸向承載力計算公式。論文運用了marc程序對地基土的應力和位移進行了有限元數值計算分析，得到了地基土的應力和位移場的變化曲線和在加載過程中樁側土摩阻力和樁端反力各自所承擔的比例；本文還在總結各國挖孔擴底樁應用情況的基礎上就擴底樁的構造進行了詳細的歸納。
  3. This multi - purpose optical metering system had adopted the twyman - green interferometric system as its center, containing an advanced digital wave surface interferometry and a kind of homodyne interferometer displacement testing method with nanometer - sized capacity. at the same time, many wide - applied metering technology, for example, the diffracted field ( fringe ) measurement, co - focal lens system, optical fiber sensors and 4f ( focal distance ) space filter system which can embody the chief principle of fourier optics well, were combined into it successfully. this instrument can firstly offer and show modern optical testing method in the laboratory for majors of information processing, instrument science, measuring and testing technology and automatic technology

    該多功能激光光電實驗系統以泰曼-格林干涉（ twyman - green ）光路作核心，包括先進的數字波面干涉技術和一種基於空間干涉原理的、納米解析度零差干涉儀位移測量方法，同時將多種新穎、工程實用價值高的測量技術和光路如衍射測量、共焦顯微技術、光纖傳感技術以及反映傅立葉光學基本光學原理的4f空間濾波系統也組合進去。
  4. Then, use the direct integral calculus method of newmark to solve solution, and get each node and element ' s displacement and stress solution vs. time

    然後，用newmark直接積分法進行求解，得到各節點和單元的位移、應力的時程解。
  5. Control observation on therapeutic effecs and effect - producing time of acupuncture and traction in 100 cases of intervertebral disk displacement

    針刺牽引治療腰椎間盤突出癥100例療效及取效時間對照觀察
  6. With the mechanics simulation of temperature load and time independent, it is on time made to monitor the corresponding load displacement field and the change tendency at any time, and is monitored the dam work regularity

    並對溫度和時效進行力學的模擬，使其及時監測在任何時刻所對應荷載的位移場和變化趨勢，從而監控大壩的運行性態及規律。
  7. Based on the principle of dspi, a kind of visual system was designed in this dissertation. which can be used in testing the off - surface displacement and deformation of the rough surface. at the same time, a multi - purpose optical metering system which contains this visual system was created and manufactured

    基於dspi原理，論文吸收統計分析思想，相對完善了該技術的實用技術體系，設計了一種dspi應用光路，該光路可用於粗糙表面離面位移和形變檢測，並依託此光路設計了一套多功能激光光電實驗系統。
  8. By means of kiba formation, k. ibt " and kibt2 segments analysis on the equivalent time stratigraphic framework, subtle traps will be predicted on stratigraphic traps and lithological traps. the results from the research indicated that : ( 1 ) this paper further indicates the control significance of southern boundary fault displacement component, which downthrown side forms syncline or anticline, and points out that 4 anticlines in south are adjustment zone and are the entering lake position of ancient river

    本論文的主要認識和結論如下： （ 1 ）進一步認識南緣邊界斷層位移量對下降盤形成次凹或橫向突起的控制意義，認出南緣的4個突起是調節帶之所在，也是古河流入湖處。這種格局導致凹陷強烈分割，並以橫向搬運為主。
  9. The best scheme was chosen after analysis and comparing and the structure was designed. at same time, the kinematics analysis was conducted, coordinate transformation matrix using d - h method was set up, and the kinematics equation direct solution and inverse solution was deduced, the velocity jacobian matrix was constructed using vector product method, and the values of displacement and velocity of some special point including the wrist point were calculated. secondly, the working space of the robot was analyzed and the axes section of practical working space was drawn

    首先，作者針對機器人的設計要求提出了多個方案，對其進行分析比較，選擇其中最優的方案進行了結構設計；同時進行了運動學分析，用d - h方法建立了坐標變換矩陣，推算了運動方程的正、逆解；用矢量積法推導了速度雅可比矩陣，並計算了包括腕點在內的一些點的位移和速度；然後藉助坐標變換矩陣進行工作空間分析，作出了實際工作空間的軸剖面。
  10. Chapter 4 time - dependent computational simulation of the response of cable - suspension feed system in gusty wind based on the time - independent structure finite element method, and with consideration of the movement laws of cabin, a 3 - d time - dependent structure finite element model formulated by a new method named iss method ( instantaneous structure supposition method ) to deal with the vibration response of cable - suspension feed system in gusty wind is presented. in the model, all sources of geometric non - linearity, cable sag and changes of cable geometry due to large displacement, are fully considered

    基於時不變結構的有限單元法，在綜合考慮饋源艙運動規律的基礎上，提出了時變系統的瞬時結構假定法，通過將懸索離散為索桿單元，建立了系統的時變有限元模型，該模型充分考慮了懸索的垂度和大變形等幾何非線性因素，應用ne 。
  11. Then, the author provided ways to control flexible support systems " displacement on the base of study the capability of flexible support systems. at the same time, the author analyzed the self - vibrating capability of flexible support systems and study the influence of parameters " changement

    同時，對柔性支承體系的動力性能進行了開拓性的研究，分析了空間柔性支承體系的自振特性，以及矢高、桿件截面、質量等不同參數對其動力特性的影響。
  12. And combining with compound analysis, this thesis has calculated and estimated the deformation and stability of slopes of the cliff debris and residual soil slope project on the project site at k15 + 183 of yong ' an section of yong - zhang highway ; ( 3 ) in the course of the cut slope excavation inner displacement has been in control of real time field monitoring

    同時邊坡開挖後期坡頂會出現回彈現象。 3 、數值計算成果表明，隨著開挖階數的增加，大小主應力在邊坡內也進行不斷的調整。邊坡開挖后坡腳處大小主應力值nlfep程序結果與ansys計算結果較為相似，兩者吻合性較好。
  13. To meet the demands for large space and flexible compartmentation of buildings, laminated vierendeel trusses are adopted in high - position transfer story structures. first the bearing characteristics are analyzed, in which reasonable stiffness ratio of the upper chord, middle chord, and lower chord is derived. then combined with an actual engineering model ( 1 8 similar ratio ), the static loading and pseudo - dynamic tests of two models for laminated vierendeel truss used in transfer story structures are conducted, in which one model adopts reinforced concrete, and the other adopts prestressed concrete and shape steel concrete. seismic behaviors are analyzed, including inter - story displacement, base shear - displacement skeleton curves, and equivalent viscosity - damping curves. a program is programmed to carry out the elasto - plastic dynamic analysis, and displacement time - history curves of the two models are derived. the test and analysis results show that the laminated vierendeel truss with prestressed concrete and shape steel concrete has excellent seismic behaviors. it can solve the disadvantages of laminated vierendeel trusses used in transfer story structures. finally, some design suggestions are put forward, which can be referenced by similar engineering

    為滿足建築物大空間和靈活隔斷要求，在高位轉換層結構中採用迭層空腹桁架結構.首先分析了其受力性能，得出了空腹桁架各構件合理的截面剛度以及布局形式.然後結合一實際工程，進行了兩榀迭層空腹桁架轉換結構模型（ 1 : 8相似比）的豎向荷載下靜力試驗以及擬動力試驗.其中一榀為普通混凝土迭層空腹桁架，另一榀配置了預應力和鋼骨混凝土，對比分析了兩模型的層間位移比、骨架曲線以及等效粘質阻力系數等抗震性能的比較，並進行了彈塑性動力分析.試驗和分析結果表明，配置預應力和型鋼混凝土的迭層空腹桁架轉換結構具有良好的抗震性能，可以成功地解決迭層空腹桁架作為轉換層結構所產生的弊端問題，最後對這類轉換層結構提出了相應的設計建議
  14. By analysis the test data, the law of temperature variation in day and temperature variation in month was got ; moreover, the probability statistics mode of day temperature difference with its statistic parameter was got too. at the same time, the year temperature difference data of walls and roofs were obtained. through the field tests, the law of thermal cracks, displacement and stress in cshbb was summarized

    對杭州市某一小砌塊試點建築進行了為期近一年的現場跟蹤監測研究，給出了小砌塊建築的日溫度變化規律和月溫度變化規律，並由此得到了小砌塊建築的日溫差概率統計分佈模式及相應的統計參數和小砌塊建築不同方位的墻體和屋面的年溫差數據；通過現場跟蹤監測，也得到了小砌塊建築的裂縫發展規律及位移和應力的變化規律。
  15. Displacement time graph

    位移時間線圖
  16. A technique of 3 - point positioning of welding seams with structure - light visual sensor is presented. with this technique, arc - welding robots can cope with the location variation of weld seams each time in batched manufacturing. on the base of suitable mathematical description, the localization problem is transformed into determining a displacement transformation matrix

    在此系統中利用機器人結構光視覺三點焊縫定位技術，使弧焊機器人可以適應批量生產中每次焊縫位置的變化，通過適當的數學描述，將焊縫定位問題轉化為確定位姿變換矩陣。
  17. According to the frndamental and the steps of this method, we cans use the linear regress filter method to make the simulation of the wind load and then we can educe the curve of the time - process wind velocity. after that step, we can get the chart of the dynamic wind load which we can deliver the crosswind into the particle wind load and put them on the corresponding cell nodes. then we can do the analysis of the dynamical wind load through the time - process analysis to get the max value of the displacement

    根據線性回歸濾波器法的基本原理和步驟，藉助相關軟體進行風荷載的人工模擬並得出風速時程曲線，進而轉化為風動力譜，由此將橫風向風力表達成節點風荷載作用於相應的單元節點上，按時程分析法對該空間桁架體系進行風荷載的動力分析，求出結構在進行風動力荷載分析時，結構相應節點對應的最值位移值。
  18. The paper formulates the dynamic analyses of hydraulic operating mechanism in large space, established mathematical model, presents methods of differential equation system, and corrects its parameters concerned in process of solution. after the unloaded characteristics calculation and test under real condition are developed for type lw - 252 breaker equipped with hydraulic operating mechanism, the time - displacement cures and the velocity - displacement cures are obtained

    本文對液壓機構的速度分析，用了大量的篇幅，建立了數學模型，給出了其方程組的求解方法，並對求解過程中所涉及的系數給予修正，在此基礎上對本課題研製的配液壓機構lw - 252斷路器進行了實際條件下的空載特性計算及實驗研究，獲得了斷路器的時間? ?位移曲線和速度? ?位移曲線。
  19. It really provides convenience to evaluate and optimize the design result. 3 ) vibration analysis has been fulfilled by calling some math libraries and graphic libraries in matlab to plot graphics such as velocity - time, displacement - velocity, step response, impulse response, gain - frequency and phase - frequency. we can know the capabilities of the spring system from the graphics

    3 、在matlab環境下調用相應的數學函數庫和圖形庫對設計的彈簧進行分析，繪制彈簧加載后系統的速度-時間響應曲線、速度-位移響應曲線、階躍響應曲線、脈沖響應曲線、增益-頻率響應曲線和相角-頻率響應曲線，根據曲線來分析系統的各項性能。
  20. Katherine brewster had me reactivated and sent through the time displacement field

    是凱瑟琳.布魯斯特重新啟動了我並派我穿越時空來到現在
分享友人
分享到 Line

分享到臉書