time-equivalent method 中文意思是什麼

time-equivalent method 解釋
時間當量法
  • time : n 1 時，時間，時日，歲月。2 時候，時刻；期間；時節，季節；〈常pl 〉時期，年代，時代； 〈the time ...
  • equivalent : adj 1 相當的，相同的，同等的。2 【化學】等價的，當量的；【數學】等價的；等量的；等勢的；【物理學...
  • method : n 1 方法，方式；順序。2 （思想、言談上的）條理，規律，秩序。3 【生物學】分類法。4 〈M 〉【戲劇】...
  1. The calculation modes of the coefficient of shrinkage and creep of the bulgy core concrete in steel tube are discussed. based on a few reasonable hypotheses and the stress - strain relation of concrete acquired by the " adjusting valid modulus depending on load time " method, a compact formula is reasoned out, which is applied to calculate the equivalent elastic modulus of the bulgy core concrete considering the affection of shrinkage and creep. so, the analysis of the affection on cfst arch bridge by shrinkage and creep can be progressed by pole - girder fem, further more, the analysis precision is quite high

    本文還對核心膨脹混凝土特殊的收縮、徐變系數計算模式展開了探討，在合理的假設前提下，採用「齡期調整的有效模量法」得到的混凝土的本構關系，推導出鋼管內核心混凝土在考慮徐變影響后的等效彈性模量計算公式，並以此為基礎採用桿系有限元方法來對鋼管混凝土拱橋進行較高精度的收縮徐變分析。
  2. So this base isolation technique has profound prospects. unfortunately there exist definite difficulties in the calculation because of the nonlinear of the base friction force. now, both the equivalent damping method and the numerical calculatin of the vibration response of the base - isolated buildings are frequently used in the calculation of the seismic response of the base - isolated building. however both of them have certain drawbacks. in this paper, the response of the building with base - isolation system is derived by the method of fourier expansion for the friction force and the earthquake response. at the same time, the sliding vibration character of inertia of a single mass structure and the sliding vibration response of a muti - mass structure are discussed. the stable condition of the sliding base isolation system of a structure is given. in the end, two circes of base fixation and base sliding are analyzed by adopting ansys

    本文利用對摩擦力和地震響應進行付氏級數展開的方法導出了基底具有摩擦隔震系統的地震反應。同時，文中從研究單質點結構的滑動振動慣性力入手，進而對多質點結構體系滑動振動反應進行探討，分別給出了結構滑動隔震的自身穩定條件。最後，本文利用ansys對基礎固定和基礎滑移隔震兩種工況進行了動力模擬模擬分析，進一步證實了基礎滑移隔規律。
  3. The way of taking one nth out of capacitor ' s the first harmonic capacitive reactance as its nth harmonic impedance is verified whit the data from tang7c. according to the approximately estimating method, the first harmonic impedance of 220kv system is calculated. on the basis of the models, this paper gives the harmonic equivalent circuit of substation and gives the b ( n ) function of the harmonic time n. when the capacitors has different combination, b ( n ) ' s value will also change, with the inputting local measurement data, the paper studies the series and parallel resonance at the substation, and deduces that the reason the capacitor ' s fuse of tang6c is frequently interrupted is that its capacitor current contains a large number of 5th harmonics, and that the reason the discharging pt of tang7c capacitor being exploded is also that the 7th and 9th harmonic currents are amplified

    據此，對該站進行了串聯諧振分析和並聯諧振分析，並結合測試數據和有關變電站的運行記錄，指出了導致該站電容器湯6c頻繁燒保險的主要原因是5次諧波電流含量偏高，引起湯7c放電pt爆炸也是因為7次和9次諧波電流被放大。針對這些導致湯陰變電站補償電容器故障的原因，提出了相應的諧波治理措施，包括針對湯6c電容器5次諧波電流含量偏高的原因，提出了停運湯6c電容器或者通過把湯sc電容器的部分容量併入湯6c電容器（湯sc其餘部分停運）以增加湯6c諧波承受能力的措施;針對# 2變低壓側7次和9次諧波電流被放大的現象，提出了在湯7c電容器上加裝一定百分比的串聯電抗器的措施。
  4. This paper researches and analyses the developments of web technology and magnetostrictive transducers from world wide region. the paper also analyes the characteristics curve of magnetostrictive transducers based on its equivalent circuit and researches the method how to make sure its syntony frequency and its electric simulation network parameters. at the same time, by using jsp technology, a magnetostrictive transducer electric simulation application is designed based on b / s three - tier system structure. the experiment data is fitted by curve fitting module. the equivalent input impedance of it with stimulate loop is separated based on the results of curve fitting and the syntony frequency and electric simulation network parameters of magnetostrictive transducers is determined by the input impedance. the method presented in this paper can determine the syntony frequency and electric simulation network parameters of magnetostrictive transducers with a better accuracy than the testing method of syntony & anti - synton y. further more, jsp, the advanced technology at current, has been used to realize a magnetostrictive transducer web electric simulation system. the system has good human computer interface and the function of resource sharing and information publishing. the research of this paper and its achievements have some practical merits in the researchful and applied fields of magnetostrictive transducer

    用java編程語言編寫的曲線擬合模塊，對輸入的實驗數據進行了最小二乘法的曲線擬合；根據曲線擬合結果可從帶激勵線圈的磁致伸縮換能器的輸入阻抗中分離出磁致伸縮換能器鐵芯在無激勵電流時由機械振動形成的等效輸入阻抗，並由此輸入阻抗確定磁致伸縮換能器的諧振頻率及電氣模擬網路參數。本課題提出的方法與傳統的諧振?反諧振法相比，能更準確地確定磁致伸縮換能器的諧振頻率及其電氣網路參數。同時，採用當前比較先進的web技術，實現了基於jsp的磁致伸縮換能器web電氣模擬系統，該系統具有良好的人機界面和資源共享、信息發布功能。
  5. The explicit finite element method ( fem ) based on the varying time - step was selected to analyse the dynamic roll - pass process ; the nodes on the leading face of the steady - state elements set was extracted and projected onto a plane to give the required mesh, also called the origin mesh ; the implicit fem was selected to analyses the inter - pass transient thermal process ; a geometric part from the mesh was generated and meshed by using the quadrilateral elements, a heat transfer analysis was selected to transfer the node temperature data ; a new model was created by using hexahedral elements, mapping the node temperature and the equivalent plastic strain on the integration points

    利用基於變步長中心差分格式的顯式積分方法分析瞬態軋制過程；提取穩態單元集節點形成截面網格；利用隱式積分方法分析軋制道次間隙瞬態溫度場；對型鋼斷面進行平面四邊形網格劃分並映射節點溫度數據；利用六面體單元構建有限元分析模型，映射單元節點的溫度、積分點的等效塑性應變，進行數值分析。
  6. Then the dynamic weighing system is equivalent to system that is time changeing and non - linearity syetem, dynamic mathmatic model is established by analysis. for the system is the arma model, parameter identification method of adaptive least square based on householder transformation is adopted

    然後，將動態稱重系統等效為二階系統，分析得出了系統為時變非線性系統，推導出了其動態數學模型，並且根據系統為arma模型，將問題轉化為參數辨識問題。
  7. Under windows nt and labview development environment, using the linear fit module, exponential fit module > general polynomial fit module of labview to design a method for fitting the experiment data, the results of curve fitting indicate that the purpose of general polynomial fitting is better than the rest. separating the equivalent input impedance of magnetostrictive transducers without stimulate current from input impedance of it with stimulate loop based on the results of curve fitting, and determining the syntony frequency and electric simulation network parameters of magnetostrictive transducers by this input impedance. finally, with labview network functions, realizing magnetostrictive transducer electric simulation system based on web server and discussing a scheme for this system network by datasocket. the method of this paper can more accurately determine the syntony frequency and electric simulation network parameters of magnetostrictive transducers than the testing method of syntony & anti - syntony. at the same time, discussing virtual instrument measurement system and how to realize magnetostrictive transducer electric simulation network system by labview network functions of network virtual instrument measurement development environment

    在windowsnt系統環境和labview虛擬儀器技術開發平臺下，首次利用labview中的直線擬合模塊、指數擬合模塊以及多項式擬合模塊，設計了一種對實驗所得數據進行曲線擬合的方法，對三種擬合方法進行了比較，曲線擬合結果表明，多項式擬合方法相對于其它兩種擬合方法效果更好；根據曲線擬合的結果可從帶激勵線圈的磁致伸縮換能器的輸入阻抗中分離出磁致伸縮換能器鐵芯在無激勵電流時機械振動形成的等效輸入阻抗，並由此輸入阻抗確定了磁致伸縮換能器的諧振頻率及其電氣模擬網路參數；最後通過labview提供的網路功能，實現了基於web服務器的磁致伸縮換能器電氣模擬虛擬儀器測試系統，並探討了通過datasocket技術實現該系統網路化的方案。
  8. The improved cyclical function method is analyzed quantitatively through using the theory of the equivalent enthalpy drop and the real - time thermal consumption analysis can done

    並應用等效焓降理論對循環函數的定量分析加以改進，進行了耗差分析。完善了循環函數法在機組局部定量計算分析的方法。
  9. A analysis of these effect to the pattern is presented. in the mean time, the method of correcting the phase errors is given by shortening or lengthening the section of sinuous feed line between couplers from the normal value. 6. the reflection characteristic of a serpentine is analyzed where the coupler is replaced by the equivalent of two ports loss network

    提出了用有耗二埠網路來等效波導耦合器的方法，對由耦合器、饋電波導和波導彎頭級聯的慢波線系統的駐波特性進行了分析計算，針對慢波線在設計測射頻率上大反射問題，討論了多種解決辦法。
  10. Based on setting up the fire safety goals, performance criterion, fire scenario and uncertainty factor, this article simulated the occupants ’ evacuation time, smoke spread, radiation flow etc and determined fire detector and automatic extinguishing device by using the developed engineering method. and so these buildings ’ fire safety goals, which have the equivalent safety level with the existing national standard, can be achieved and those problems, which caused by some incompliment requirements or the existing codes not adapting to the practical need, can be solved

    針對這類建築存在的典型問題，通過設定消防安全目標、確定性能判據、建立火災場景，考慮不確定因素，運用已開發的工程學方法對人員安全疏散時間、煙氣蔓延、輻射熱通量等進行模擬計算，對火災探測和自動滅火設施進行分析選擇，認為大型書城建築採用至少與現行國家標準的規定等效的方法來實現建築物的消防安全目標，能夠解決現行標準與實際需要不相適應或某些不完善的規定所帶來的問題。
  11. The calculation method of technical parameters of maximum output power, the short time power and continued power ( equivalent heating ) in electric braking are derived from analyzing the relationship of maximum regenerative power with resistance value of ground absorption equipment, model of traction power supply, train circuit and network voltage drop while performing electric braking

    通過分析列車電制動時的最大再生功率與電阻吸收裝置的電阻值、電制動時刻牽引供電系統的模型、列車電流、網壓降之間的關系，導出了列車電制動時最大輸出功率、地面電阻吸收裝置的短時功率和持續（等效發熱）功率等技術參數的計算方法。
  12. This paper presents the element stiffness matrix and equivalent node force of the variable cross - section bar. so the approximation in structural analysis is avoided, and the calculation capacity of equivalent frame method is also developed. this helped the engineers avoid the fem, which consume much time and is difficult to master

    本文對板帶寬度變化的板柱結構推導了變截面直桿單元的單元剛度矩陣和等效結點荷載列陣，避免了在結構分析時所作的近似，也擴大了等代框架法的計算范圍，使工程技術人員免於使用佔用機時、難于掌握的有限元分析法。
  13. The mode superposition method, based on equivalent linearization and forcing decoupling method of non - classical damping matrix of energy dissipation systems, is the just one. at the same time, iterative process will increase computing workload and forcing decoupling method increase error

    基於等效線性化的強行解耦振型分解法在一定程度上符合此要求，但此方法存在著迭代計算工作量大、強行解耦增大計算誤差的不足。
  14. A high - speed sampling system for echo signal of impulse gpr based on equivalent time sampling method is presented, and significant circuits including step sampling pulse generator and sampling gate circuit are designed

    摘要提出了一種基於等效時間采樣方法的沖擊型探地雷達回波信號高速采樣系統，設計實現了等效時間采樣的關鍵電路，包括步進采樣脈沖發生器、采樣門電路。
  15. The rails are affected by the skin effect for its large permeability and size. the track time constants are not constant due to the skin effect. for the calculation of the rails impedance, the method of equivalent cylindrical conductor is developed

    由於鐵軌很大的磁導率和截面尺寸，致使其阻抗在電磁暫態過程中受到了集膚效應的影響，從而使得鐵軌的時間常數在暫態過程中並非是一個常數。
  16. The rules obtained from the background modal analysis method based on the quasi - steady assumption in frequency - domain are similar to those obtained by the analysis method in time - domain, and the influence of high modes can be considered. finally, the dissertation suggests that for engineering design, it is better to use equivalent wind load factor defined the ratio of wind - induced total displacement to static displacement for computing the equivalent static wind load of long - span grid roof structures, and the equivalent wind load factor of the roof of taizhou stadium is calculated

    最後通過對大跨網架屋蓋結構的風振系數的研究，提出了在實際工程設計中，採用位移風振系數來計算大跨屋蓋的等效靜力風荷載既正確又方便使用，並且給出了臺州體育中心看臺屋蓋進行分塊統計后的位移風振系數，以供設計參考。
  17. Comparing the fitted expression with the established theory expression of the angular velocity, the equivalent viscous damping coefficient is gained. the closed form algorithm of the state space method is employed to solve the system dynamic equation with time - varying coefficients. the dynamic problem of a linkage mechanism with four joints is taken as example to show that the presented models and methods are correct and practicable

    引入求解線性微分方程的狀態空間法，並對其求解時變系統運動微分方程的具體步驟進行了推導；在此基礎上將實測獲得的運動副等效粘性阻尼系數代入系統動力學方程，求解后獲得了考慮運動副阻尼的平面彈性四連桿機構的模擬結果；結果表明運動副的阻尼在一定程度上對振動具有抑制作用。
  18. Then analyze the motion and dynamics ; induce the dynamics equation ; use multiple - step gear estimation and correction to solve the time domain ; use equivalent method of statistical linearization to solve the frequency domain

    進行了運動學分析和動力學分析，推導了動力學方程，採用多步gear預估?校正法進行時域求解，採用等效的統計線性化方法進行頻域求解。
  19. And the paper analyzed the relations between the errors of the components and load distribution among the backstop piece, and put forward a method of translating the errors into a equivalent error. for the occasion of several backstops being used at the same time, the paper put forward a project of uniform load among the backstops

    分析了誤差對逆止器內部逆止塊的載荷分佈的影響，並提出各種誤差轉化為等效誤差的方法；對多個逆止器同時使用的場合，提出了均載方案。
  20. At the same time, the program corresponding to the proposed method is compiled in fortran90, which is used to analyze the influence of several factors on behaviour of barrettes, including ratio of length to width, ratio of depth to equivalent diameter, ratio of modulus of pile to soil, possion ' s ratio, the finite layer etc. many useful conclusions are obtained from the above analyse

    該方法考慮了壁板樁樁身橫截面的非軸對稱性，並用fortran語言編制了相應的程序，進而分析了多種因素對壁板樁承載特性的影響，包括長寬比、樁徑比、樁土剛度比、泊松比以及有限壓縮層深度等。
分享友人
分享到 Line

分享到臉書