trough section 中文意思是什麼
trough section
解釋
槽形截面-
Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle
流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。 -
In this way, when obturation cubage leave absorb oil cavity it connects the eduction oil cavity with the v trough and with the increasing of the turning angle, the size of the cross section of v trough become bigger and bigger, which make the pressure between the cavity of two blades much higher and higher, and until it completely connects the eduction oil cavity, it reaches the pressure of the eduction, and it can effectively reduces the fluid noise caused by high pressure return flow
這樣，當密閉容積離開吸油窗口之後，通過v型尖槽逐漸與排油窗口連通，隨著轉角的增加， v型尖槽通流截面積逐漸增大，這就使兩葉片間容腔內的壓力逐漸升高，直至完全接通排油窗口時，才升壓達到壓油腔的壓力，這樣可以有效地降低因高壓迴流而引起的流體噪聲。 -
The reason to creates this kind of destruction to be very many, the main of them is that the apron partially has not been able fully to display it to eliminate energy affect so causes the ditch bed to wash out, forms flushes the pit, leading to the apron, to guard against flushes the trough and both banks slope protection destruction, for a long time, disappear power design of plunge basin and layout have been focused on disappear power. but not to give the enough value on uses the sea to inundate the section to disappear power and adjust speed to reduced downriver washes out
水閘閘下沖刷破壞的部位絕大多數發生在消力池下的海漫和防沖槽處，造成這種破壞的原因很多，其中很大一部分是由於海漫部分未能充分發揮其消能作用而引起渠床沖刷，形成沖坑，導致海漫、防沖槽及兩岸護坡的破壞。一直以來，人們把消能的研究重點放在消力池的消能設計及平面布置上，而對海漫段消能及調整流速功能研究甚少，至於對海漫加糙水流運動建立數學模型，在國內外還很少見相關的論文資料。
分享友人