ultimate bearing failure 中文意思是什麼
ultimate bearing failure
解釋
極限承載損壞-
Though much progress has been achieved in previous study, there still remains a lot to be studied and perfected. the thesis is devoted to study on the multi - ribbed slab wall, the main bearing member in mrss, including its mechanism, failure mode, aseismic capability, mechanical models, ultimate bearing capacity and aseismic design based on control. the paper mainly accomplished such work as follows : 1 ) based on test research on multi - ribbed slab wall, the paper proposed the member ' s failure modes under horizontal loads, analyzed the co - performance between the inner frame and the infilled silica bricks and that between the slab and the outer frame, discussed the wall ' s bearing capacity, rigidity, deformation, ductility and energy dissipation ability in different modes, and put forward a simplified mechanical model of the slab wall under vertical loads
本文針對密肋壁板結構的主要受力構件? ?密肋復合墻體為研究對象，就其受力機理、破壞模式、抗震性能、三階段力學模型、極限承載能力以及基於控制的抗震設計方法等進行了較為詳細的研究，完成的主要工作有： 1 ）通過對密肋復合墻體在水平低周反復荷載和單調荷載作用下的試驗研究，提出了墻體的主要破壞模式；分析了框格與內部填充砌塊、墻板與外框的共同工作的受力特點；探討了不同破壞模式情況下墻體的承載能力、剛度、變形、延性、耗能等抗震性能，並給出了豎向荷載作用下密肋復合墻體的簡化力學模型。 -
The results indicate that the different construction methods will have influence on the mode of the internal force redistribution, however, the methods will not cause influence on the mode of structure failure, and the ductility of the final structure will make the ultimate bearing capacity of the beams cast by the different methods get close to an identity
結果表明：不同施工方法會影響內力重分佈的模式，但不影響結構的破壞模式，最終結構的延性將使不同施工方法梁的極限承載力趨近一致。 -
Based upon the experimental research and nonlinear finite element calculation, and the analysis of joint failure modes, a set of formula was proposed to predict the ultimate bearing capacity of cfrst joints : 1 ) the ultimate bearing capacity of t -, y -, x - compression joints and k - compression branch joints can be predicted according to the failure model of transverse local compression
基於試驗研究和非線性有限元數值計算，通過對矩形鋼管混凝土桁架節點各種可能破壞模式的分析，提出了矩形鋼管混凝土桁架節點承載力計算的破壞模式和相應計算公式： t 、 y 、 x型受壓節點和k型受壓支管節點承載力按橫向局部承壓破壞模式進行計算。 -
Combined with code for design of building foundation and code for foundation treatment ( in china ) these two methods are replenished here. 6. this paper deduced the formula of ultimate bearing capacity based on the principle of limit equilibrium and the formula of determining the length of reinforcement based on equilibrium of anchoring segment outside shear failure lines by analyzing two limit equilibrium modes, those are limit breaking and pullout of reinforcement
（ 8 ）三維土工格室的承載力計算公式相當缺乏，論文中指出r . m . koeme :提出的土工格室承載力計算公式不符合力的平衡原理，並推導出土工格室加筋地基承載力的改進公式，用算例比較了有無土工格室加筋的效果。 -
Ultimate bearing failure
極限承載損壞 -
Also the failure modes and the cracking torque, original stiffness, ultimate torsion strength and ductility are discussed in this case. the factors affected torsion bearing capacity of high - strength concrete frame column is analyzed too. the seismic performances of normal - strength and high - strength concrete frame column subjected to biaxial eccentric compression, shear and reversed torque are studied
以軸壓比和相對偏心距為主要研究參數，揭示高強鋼筋混凝土構件在單向、雙向偏壓剪單調、反復扭矩作用下的破壞特徵、開裂扭矩、剛度、強度、延性等特性，分析了影響高強混凝土框架柱抗扭承載力的因素。 -
And the theoretical a nalyses done in this paper are listed below : first, the experimental data on the members of varied parameters under torsion demonstrate the general rule of the deformation while the tubular is under torsion. the paper establishes three phases of the deformation of the tubular under torsion, namely, the elastic deformation, the elastic - plastic deformation, and ultimate failure. through regression analysis, a simplified method is proposed for calculating the capabilities of the tubular under elastoplastic torsion, and the formulary for bearing value, is also recommended as a reference in engineering design
本文根據不同參數的構件受扭性能試驗結果，研究了該結構受力變形全過程的基本規律，提出了受鈕全過程的三個工作價段，即彈性變形階段，彈塑性變形階段和極限破壞階段，經分析回歸得到扭轉全過程彈塑性的簡化分析方法及承載力計算公式，可供工程設計參考；同時根據本文的彎扭試驗結果以及對離心鋼管混凝土構件進行的理論分析，推導了彎扭試驗相關承載力的關系。 -
But the methods can only treat some simple cases, can not deal with muti - layered subsoils. therefore the mechanism of failure and the methods of estimating the ultimate bearing capacity should be further studied for inhomogeneous medium. in this paper, in - site test, model test with different scales and elastoplastic fem was performed to study the problem
這兩種方法只能解決簡單非均質介質基礎的承載力問題；對于基礎介質構成較復雜的情況，計算結果往往和實際值有很大的誤差，因此對于非均質介質基礎的破壞模式及極限承載力的計算需要更深入的研究。 -
By tests of 9 specimens subjected to biaxial eccentric compression, shear and reversed torque, the failure modes and the varying laws of cracking torque, original stiffness, ultimate torsion strength and ductility are discussed, with the change of axial stress level and relative eccentricity. then, the cracking bearing capacity, the ultimate capacity and the deformability of the specimens are obtained
通過9根承受雙向偏壓、彎、剪構件在反復扭矩作用下的試驗研究，以軸壓比和相對偏心距為主要研究參數，揭示鋼筋混凝土構件中雙向偏壓剪反復扭矩作用下的破壞特徵、開裂扭矩、剛度、強度、延性等特性和耗能性能，從而確定其開裂承載能力和極限承載能力及變形性能。 -
Based on the simulating results of simply - supported box girders ( 39. 1m ) and continuous box girders ( 2 x 40m ), the paper emphatically analyzes the full mechanical characteristics of psbget and the bend failure states of the right section. the influence of different areas and eccentricities of external tendons on ultimate bearing capacity and ductility is studied in detail. the differences of ultimate bearing capacity and the mechanical characteristics between the se
Lin簡支箱梁和2x40m連續箱梁為例，本文較全面地分析了預制節段拼裝體外預應力混凝土箱梁全過程受力特性和正截面彎曲破壞形態；研究了不同預應力配筋面積和預應力筋重心高度對預制節段拼裝體外預應力簡支梁極限承載力和延性的影響，以及體外預應力節段簡支梁與體外預應力、體內有粘結預應力整體簡支梁極限承載力和受力特性的差異。 -
Guarantee the safety of this project. this experiment focus on the failure mode and the ultimate bearing capacity of these columns. besides, this experiment also study the rule of the development of the deflection, the crack, the strain and the stress with the process of this experiment.
通過此次試驗重點研究重慶大劇院縱向框架細長柱的破壞形態（是強度破壞還是失穩破壞）和極限承載能力，同時研究構件的變形、裂縫、應力應變隨加載的發展變化規律及其破壞過程，為本工程及今後此類細長柱結構體系的設計提出一些有益的建議。
分享友人