ultimate tensile strength 中文意思是什麼
ultimate tensile strength
解釋
根限抗拉強力-
The variation of ultimate tensile strength with length for amosite crocidolite, chrysotile is shown in table 2. 10.
鐵石棉,青石棉和溫石棉的極限抗拉強度隨長度的變化情況見表210 -
The variation of ultimate tensile strength with length for amosite crocidolite, chrysotile is shown in table 2. 10
鐵石棉,青石棉和溫石棉的極限抗拉強度隨長度的變化情況見表2 10 -
Tensile ultimate strength of steel
鋼材鋼筋抗拉極限強度18 -
Influence of interfacial damage on ultimate tensile strength of cross - ply laminates
界面損傷對正交疊層板最終拉伸強度的影響 -
The influence of nondimensional parameters and on failuremode and ultimate tensile strength of gusset plate connections to slotted tubes arestudied
、鋼管直徑與鋼管壁厚之比?對該類節點破壞模式和極限承載力的影響。 -
Analysis ofnonlinear finite - element for ultimate tensile strength of gusset plate connections toslotted tubes with ansys program are carried out in this dissertation
本文採用通用有限元程序ansys對管板節點進行非線性有限元分析研究。 -
A full - scale experimental study and associated nonlinear finite element analysiswere undertaken to study the ultimate tensile strength of gusset plate connections toslotted tubes in this dissertation
本文研究的主要內容包括管板節點受拉極限承載力非線性有限元分析和足尺試驗研究兩部分。 -
The test result of the rene95 sample showed that the maximum ultimate tensile strength can be as high as 1400mpa and has reached 97. 9 % of that of the sample fabricated by powder metallurgy ( pm ). the plastic elongation of the test sample can even exceed that of pm. the ultimate tensile strength of the test sample grown from single crystal substrate has surpassed 6 % of that of grown from the stainless steel substrate, at the same time the plastic elongation surpassed 40 %
對成形試樣的力學性能測試結果表明,強度方面_ b最大為1400mpa ,已經達到了粉末冶金的97 . 9 ,塑性方面甚至超過了粉末冶金的水平;以單晶為基材的成形試樣其最大拉伸強度要比不銹鋼為基材的試樣高6 ,延伸率要高40 。 -
1. experiments on uniaxial tensile of cfrp and gfrp are carried out, in which the tensile strength, young ' s modulus and ultimate deflection of frp are measured. the influence on tensile behavior caused by different adhesives is analyzed, and the standardization problem on tensile test methods is discussed
設計了加載裝置和測量應變裝置,測試6種不同纖維片材和粘結劑組合的抗拉強度、彈性模量、極限應變,並分析不同粘結劑對纖維片材拉伸性能的影響,最後對纖維片材拉伸試驗的標準化問題進行了簡單的探討。 -
Considering the randomness of strength and deformation of concrete material, a mathematic approach of producing random variables series of concrete ultimate tensile strain is proposed
摘要針對混凝土構件材料強度和變形性質的隨機性,採用數學方法提出構造混凝土極限拉應變數列的原理。 -
Vulcanized rubber - determination of tensile strength and ultimate elongation at high temperatures
硫化橡膠高溫拉伸強度和扯斷伸長率的測定 -
The correlation between the compressive strength and axial tensile strength of rcc with placing joint and ultimate tensile strain of placing joint of rcc layers have been obtained
通過試驗研究給出有層面碾壓混凝土抗壓強度、層面軸拉強度與層面極限拉伸值間相關關系。 -
Textiles. tests on knitwear. determination of the ultimate tensile strength
紡織品.針織品試驗.極限拉伸強度的測定 -
The effect of the crack eccentricity ratio on the stress intensity factor and the ultimate tensile strength for cracked ductile plates was investigated in this paper
摘要疲勞裂紋對船舶結構強度具有不可忽視的削弱作用,在過去的研究中,主要從斷裂力學的角度對疲勞裂紋應力場進行分析,而對于靜態裂紋板的極限強度的探討相對較少。 -
To generalize the eccentricity ratio effect on ultimate tensile strength of ductile plates, the elesto - plastic finite element method is undertaken and a mathematical transition expression of normalized ultimate tensile strength of center - cracked, eccentrically cracked, edge - cracked plates is accordingly deduced
對于偏心裂紋延性板,採用彈塑性有限元進行了大量的組合計算,分析了相對裂紋長度、材料屈強比和裂紋偏心度對板的拉伸極限強度的影響,並給出了方便計算的回歸公式。
分享友人